Jump to content
SAU Community

Post Up Your R33!

nizmo_freek

By nizmo_freek,
in Photography

 Share

Recommended Posts

  • Replies 5.5k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

jays r33 gtr
jays r33 gtr

Recent pic img host

GTR-N1
GTR-N1

Off the boat from Japan. Just a peek.   TE37 Magnesium put aside for LMGT1   Not detailed for a while yet. After compliance, it should happen.   Titaniu

Run-It-Hard
Run-It-Hard

My old girl got a make over recently, and I finally got my Ordens on her too!

Posted Images

DRD-00F Grand Master

DRD-00F

Posted
Posted

well again, IN THIS STATE, it doesn't matter if it's stock or not, there's a set of rules and guidelines that you have to abide by to do it.

It has to be viewable from 45 degrees on either side of the centre of the car, 5m away.

I believe those are the measurements, I could be wrong...

Basti Grand Master

Basti

Posted
Posted
Always been illegal. Been pulled over before the kit and cop said i could lose 3 points for it. I know people that have been done for it too. + you get a fine.
well again, IN THIS STATE, it doesn't matter if it's stock or not, there's a set of rules and guidelines that you have to abide by to do it.

It has to be viewable from 45 degrees on either side of the centre of the car, 5m away.

I believe those are the measurements, I could be wrong...

Kris, this appies in Vic. ADR rules if im not mistaken. have a look on vicroads website. you should be able to find it. sidemount that mofo

Stealthynsa Proficient

Stealthynsa

Posted
Posted
"Niceay?" - Not really. LOL

Looks clean mate, but definitely need some new rims, plus perhaps you should also tint your car darker too.

tint my car darker? what are u talking about... if ur talking about the windows they are just darker then legal,

also the quote niceay? not really... is pretty lame what car do u drive put it up

krzysiu Grand Master

krzysiu

Posted
Posted
well again, IN THIS STATE, it doesn't matter if it's stock or not, there's a set of rules and guidelines that you have to abide by to do it.

It has to be viewable from 45 degrees on either side of the centre of the car, 5m away.

I believe those are the measurements, I could be wrong...

Well obviously im in victoria and i know the rules... your 45 degrees one is correct. But here it MUST be foward facing parrerel to the chasis or some shit (in victoria). I HAVE had it to the side. Everytime i got pulled over it was mentioned. After been pulled over after driving it for 100m i think ill keep it in the middle... even though it does look much tougher on the side.

Stealthynsa Proficient

Stealthynsa

Posted
Posted
Well obviously im in victoria and i know the rules... your 45 degrees one is correct. But here it MUST be foward facing parrerel to the chasis or some shit (in victoria). I HAVE had it to the side. Everytime i got pulled over it was mentioned. After been pulled over after driving it for 100m i think ill keep it in the middle... even though it does look much tougher on the side.

im pretty sure its www.justjap.com that sell a side mound bracket u can screw into ur bar, :D problem solved

DRD-00F Grand Master

DRD-00F

Posted
Posted
Well obviously im in victoria and i know the rules... your 45 degrees one is correct. But here it MUST be foward facing parrerel to the chasis or some shit (in victoria). I HAVE had it to the side. Everytime i got pulled over it was mentioned. After been pulled over after driving it for 100m i think ill keep it in the middle... even though it does look much tougher on the side.

I never let a street cop be the be all and end all on road rules cause all my run ins with them show that they don't know shit...

Mine has been mentioned by police pretty much every time I've been pulled up as well, but my point is, SOME TIMES, THE POLICE GET IT WRONG!

105.11 Visually inspect the front and rear number plates.

Reasons for rejection

f) Characters on the number plate are not clearly visible from a

distance of 20 metres at any point within an arc of 45 degrees from

the surface of the number plate above or to either side of the vehicle

Here. I tried to find the rules on vicroads but the search is pretty crappy... sorry man >_< might be under the RWC guidelines.

nzm033 Proficient

nzm033

Posted
Posted
My old wheels make it look awesome mate!

Getting my guards rolled this weekend so I'll be rocking the same set of very fresh wheels as you :D

ur old rims make my car!!! I had to roll the guards aswell. I still goto put spacers on and lower

Did u powder coat the centers or urs? Im not sure if i can be bothered...i was planing on powder coating the rears white but not sure

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 33GTRV
      Rb26 iron block limit

      By 33GTRV · Posted

      Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
    • GTSBoy
      RB25DET Series 1 & Series 2 Gearbox Identification

      By GTSBoy · Posted

      thumbsup
    • AdiR34
      Did tie rods. Steering now not "springing" back.

      By AdiR34 · Posted

      Appreciate everything guys. I did go ahead and get an alignment... most of my complains are solved. Car is not perfect, but it's good enough. If I notice uneven tire wear or anything I'll just take everything back to stock.  Thanks again!
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      They still have not shipped the 550cc injectors as they weren't in stock, so in theory I could ask to get the 440cc ones instead, if those work better in my scenario. They're the same price so really shouldn't be an issue. Unfortunately I am not so knowledgeable in most parts of tuning so I wasn't sure what's best to choose between the two. 440cc ones are the lowest they have (not in stock, but available to buy nonetheless).
×
×
  • Create New...