Jump to content
SAU Community

Recommended Posts

yeah im with G_Force on this one, as im looking at changing out the old plugs next weekend and need some idea of what i should put in. After the split dump/front pipe install the 34 runs at slightly higher boost now, should this slight increase mean i should gap down to say .7 or just stick with the .8 gap? also, im too woundering what the heat range should be.

:(

Edited by RyanN

man, the dreaded R34 coilpacks strike again, these things break just looking at them the wrong way!

i got split fires, problem solved. Got some NGK Iridiums as well from kudos motorsports, not sure of the exact model. But yeah, you can't gap iridiums but i'm almost 100% sure they aren't less than 1.0mm, they're 1.0mm +, that was recommended to me (no power mods at all)

a set of splitfires is about the same price as a set of brand new packs from Nissan, so it's a bit of a no-brainer if you can't go the DIY fix (epoxy/tape)

...should this slight increase mean i should gap down to say .7 or just stick with the .8 gap?

From what I've read I believe you want the largest possible gap that will still create sufficient spark. Unless you've got some serious mods (i.e. you just have a full exhaust), I think 1.0 is fine (down from the 1.1 factory recommendation).

Edited by McCracken

Well like i said im running 12psi, and possibly even up to 14psi, will see wot my tuner can do when i get it tune.

With this boost the std 1.1 gap would blow out i believe, Will check my coils but i think they r fine, its just misfiring a lil round the top end atm.

So anyone kno the no for the NGK i need? V-power coppers 0.8 gap, not sure of heat range. Is there someone i can get these off online?

From what I've read I believe you want the largest possible gap that will still create sufficient spark. Unless you've got some serious mods (i.e. you just have a full exhaust), I think 1.0 is fine (down from the 1.1 factory recommendation).

ok thanks mcCracken, do you know if the heat range should stay the same?

also, on that topic of coilpacks, i used to have a problem with them atleast twice a week however once i replaced the vacumm sensors hose (as it kept falling off) everything is now fine ;) , i haven't had any probs with the coilpacks for a least a year. :)

ok thanks mcCracken, do you know if the heat range should stay the same?

also, on that topic of coilpacks, i used to have a problem with them atleast twice a week however once i replaced the vacumm sensors hose (as it kept falling off) everything is now fine ;) , i haven't had any probs with the coilpacks for a least a year. :)

To be honest, I'm unsure. Just my own opinion, unless you have a seriously deviate from factory specs stick with factory recommendations. Having said that, I see you have a FMIC and some other stuff. Perhaps ask a tuner or look around on the forums.

Some extra information I thought might help others. I just spoke to a respectable Melbourne tuner and he even suggests gapping to 0.6mm on the GTt's to prevent misfiring on high boost. He even said they've gone as low as 0.5mm on R34 GTR's. It's his opinion that the ignition system on the R34's are weak as piss. Failing that, swap around the coils and then eventually new Splitfires.

Edited by McCracken
picked up some sparkys today, BCPR6ES gapped at .8 however the neos are meant to have a heat range of 5 right? .... take em back and swap them or stick with the 5? :(

Absolutely no problem using 6s in the NEO. If you've got a few mods, the 6 would be a better choice anyway.

Lithius any problems with running the BCPR6ES-8 in ur GT-T? I heard they r a shorter plug than the factory std PFR6G-11.

I was planning to use the BKR6E, similar to the BCP6ES except they have the V-power(grooved) electrode. Some have said to me stick with the factory plug n just gap them down to 0.8.

Not sure if anyone still needs to know but I'm running NGK BCPR6ES-8 in my R34 GTT. They cost me about $4 each from repco. I think they're the same plugs people run in the R33.

Well, a workshop put some Iriways in there and it developed a big misfire on boost. Went to autopro with one of the Iriways and they gave me some BKR6ES-11 to try, I regapped them to .8 and put them in... still misfiring. Eventually I got splitfires but it was still misfiring with the Iriways, so I put the gapped BKR6ES in there and the misfire dissapeared.

My plugs were a bit fouled from when I played around with my AFM settings so I thought i'd try some BCPR6ES-8 (I think they're actually longer than both the Iriways and BKR6ES) and they work fine... No problems at all thus far.

The length difference between the BKR (ISO tip) and BCPR (JIS tip) series is the length from the base to the insulator end (ie where the coil attaches to). The electrode etc are identical.

iso_jis.jpg

I have used both JIS and ISO types in my car with no differences (so long as the coil pack contacts the spark plug properly it shouldn't be a problem for anyway).

Edited by Busky2k

just spent the morning changing the plugs (well i woke up at 11:00 :) ), it had NKG PFR6G-11 in there already gapped to .81 (previous owner i guess); replaced them with the NGK BCPR6ES gapped at .81, everything runs good.

.... however i dont if its just me but i seem to get shocked by the car now after i've been for a drive since i changed the plugs. would coilpacks arcing create this shock?

:dry:

Edited by RyanN
You are thinking of static shock? Probably not the coilpacks...

yeah, its increased after i changed the plugs for some reason, it cant be what im im wearing as i never got a shock before from the clothes.

my R34 has been shocking me more recently? i've got NGK iridiums and Splitfire coilpacks... but it definitely wasn't the packs, maybe after i changed the sparkies, but i thought it was when i put my HID kit in (gotta ground stuff to the car)?? maybe it was the sparkies then? my carpets are still quite lush and fluffy, i thought it might have been those as well :dry:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...