Jump to content
SAU Community

Recommended Posts

Ive had my car (stock wheels) sittign on 30 PSI (?). I noticed the car didnt roll too well when up on a hill. Because I drive a lot on freeways I pumped my tyres up to 40 PSI... the car rolls much better now and I am getting better economy, I know that I now should take care in the wet as the tyres are not as grippy.

Whats your tyre pressures?

Link to comment
https://www.sau.com.au/forums/topic/130975-tyre-pressure/
Share on other sites

For stock rims i found 32 front, 30 rears (300zx rims) the best

But then again i didnt drive around with much thread.. maybe 2mm max on rears.. Plus my tyres were old.

Anyways i have pumped the fronts to 38 once and it seemed fine.

I do a lot of freeways also, but cant tell the difference on highways tho lol

Got 235s on fronts now with 30psi pressure.. Seems fine

Edited by siddr20
Link to comment
https://www.sau.com.au/forums/topic/130975-tyre-pressure/#findComment-2422881
Share on other sites

I'm running 36 all round, because that's what the manufacturer recommends (B/S Potenza G III, 235/45x17).

When it's wet, INCREASE front tyre pressures - holds the tread open for better water dispersion.

Link to comment
https://www.sau.com.au/forums/topic/130975-tyre-pressure/#findComment-2425245
Share on other sites

That's the reason for owning your own tyre gauge - at least it will be consistent between servos.

You're telling me dude!

I hope not much damage was done to the tyres, no wonder why the ride was crap.

I got back from overseas for 2 months and figured I needed to check pressures and so I did, unbeknown to me the servos automatic tyre pressure thingo was not accurate

Link to comment
https://www.sau.com.au/forums/topic/130975-tyre-pressure/#findComment-2429533
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
    • That worked out PERFECTLY! Thank you big time to JJ. He was able to swap me his stock diff. He drove all the way to me as well. Killer! Removal & install was pretty straightforward. The diff itself is HEAVY. So that’s a 2 man job.  Man does the car drive nice now! Couldn’t have worked out any better 👌
×
×
  • Create New...