Jump to content
SAU Community

Here's An Interesting Problem To Solve

m0t4v4ll1

By m0t4v4ll1,
in General Maintenance

 Share

Recommended Posts

m0t4v4ll1 Enthusiast

m0t4v4ll1

Posted
Posted

Today i noticed my front LH light was out, so i changed the bulb, still didnt work, so i realised the fuse was blown, easy enough 20 cents later problem fixed

Driving home at night i noticed that the cluster backlight wasnt... well, backlit PROBLEM 1

Then i took the car in to the self wash and started vacuuming, i turned on the lights and noticed that on the first setting and nothing, no lights, then when i look at the back of the car, the rear lights arent on either? - PROBLEM 2

Then i put it on the last light option (the top one, u kno) and the front lights work, but the back lights aren't lit up.... ----BUT when i put my foot on the brakes, they work, but only when i have my foot down... so they do work, but there must be something up

HELLLLLLLLLLLLLLLLLLLLLLLLLLLP

lol

m0t4v4ll1 Enthusiast

m0t4v4ll1

Posted
  • Author
Posted
maybe dimmer switch fault. or earth?

occasionally my GTR LH light goes out u tap it and it will work again. same with the LHF indicator. ??? bad earth..

the LH light is fine, its just those other two problems... the cluster backlight, and the rear brake lights... do these things have fuses? and where r they?

cowie165 Veteran

cowie165

Posted
Posted

Headlight switch here: http://www.skylinesaustralia.com/forums/in...howtopic=115618

Your switch is stuffed as T04GTR said. There are three contacts within the switch. As you rotate the headlight dial on your dash, you change which terminals are touching the contacts, therefore changing the lights.

The contacts do not move in an incremental/accumulative way - that is, if the contact for the parkers/dimmer is stuffed, you can still switch to the next one and your headlights will come on. Think of it as though each time you click the dial, the switch is telling your lighting system to switch on/off. When you click to the next one, it send the next set of orders to your lights, but doesn't repeat the first set.

I know it's a weird explanation but that's where your problem lies.

Azza ring Just Jap in Sydney and they'll sell you a switch for ~$50. You can try fixing yourself too if you're keen on DIY.

And finally, there actually isn't a relay in the switch and therein lies the problem. The switches burn out due to excessive current melting the plastic pots within the switch. The only way around it is to rewire the switch to trigger a relay and use the relay to activate your lights.

Cheers dude! :D

  • 3 weeks later...
m0t4v4ll1 Enthusiast

m0t4v4ll1

Posted
  • Author
Posted
Headlight switch here: http://www.skylinesaustralia.com/forums/in...howtopic=115618

Your switch is stuffed as T04GTR said. There are three contacts within the switch. As you rotate the headlight dial on your dash, you change which terminals are touching the contacts, therefore changing the lights.

The contacts do not move in an incremental/accumulative way - that is, if the contact for the parkers/dimmer is stuffed, you can still switch to the next one and your headlights will come on. Think of it as though each time you click the dial, the switch is telling your lighting system to switch on/off. When you click to the next one, it send the next set of orders to your lights, but doesn't repeat the first set.

I know it's a weird explanation but that's where your problem lies.

Azza ring Just Jap in Sydney and they'll sell you a switch for ~$50. You can try fixing yourself too if you're keen on DIY.

And finally, there actually isn't a relay in the switch and therein lies the problem. The switches burn out due to excessive current melting the plastic pots within the switch. The only way around it is to rewire the switch to trigger a relay and use the relay to activate your lights.

Cheers dude! :)

just finished exams so i'll check this out for sure!!!

i owe u a beer regardless... i've noticed uve saved my ass on numerous occasions

thanks mate :cool:

m0t4v4ll1 Enthusiast

m0t4v4ll1

Posted
  • Author
Posted
just finished exams so i'll check this out for sure!!!

i owe u a beer regardless... i've noticed uve saved my ass on numerous occasions

thanks mate :cool:

lol i noticed ur in the blue mountains though errrr that'll be hard... how much is courier beer? hehehe

btw my folks used to have a farm house up in lithgow when i was a tike... u from around there?

m0t4v4ll1 Enthusiast

m0t4v4ll1

Posted
  • Author
Posted
lol i noticed ur in the blue mountains though errrr that'll be hard... how much is courier beer? hehehe

btw my folks used to have a farm house up in lithgow when i was a tike... u from around there?

lol another point

i was wondering..... my bro has an r32 gtst, would i be able to dismantle and take out his plug and swap it over wit mine to see if it works? are they the same plugs? hehe.. .yes i'm a tightass terry atm

cheers again

Godzilla32 Veteran

Godzilla32

Posted
Posted

Sounds strange to me. Before you rush out and buy a new switch double check that the same fuse isnt blown again. All those things run on the same fuse. If there is a short somewhere it will continue to blow the fuse. The reason your brake lights work is because they aren't on the same circuit.

If your LH light was out, im assuming parker light, why would only one of them be out if the fuse was blown? The whole circuit would have failed, therefore all of lights on the same circuit wouldnt be working.

Then again it could be the switch.. You could test it for continuity.

m0t4v4ll1 Enthusiast

m0t4v4ll1

Posted
  • Author
Posted
Sounds strange to me. Before you rush out and buy a new switch double check that the same fuse isnt blown again. All those things run on the same fuse. If there is a short somewhere it will continue to blow the fuse. The reason your brake lights work is because they aren't on the same circuit.

If your LH light was out, im assuming parker light, why would only one of them be out if the fuse was blown? The whole circuit would have failed, therefore all of lights on the same circuit wouldnt be working.

Then again it could be the switch.. You could test it for continuity.

ah the front LH was out.... sorry should have just written LHF was out

i'm gonna go to the garage now and dismantle the baby... tinker with her a bit, n see wats up..

will bring the laptop with me if anyone else has ideas i'll still be online :(

CHEEEEERS big ears

cowie165 Veteran

cowie165

Posted
Posted
lol another point

i was wondering..... my bro has an r32 gtst, would i be able to dismantle and take out his plug and swap it over wit mine to see if it works? are they the same plugs? hehe.. .yes i'm a tightass terry atm

cheers again

G'day Azza. Sorry mate, been out of town for a few weeks. Don't worry about the beers, cause I sure owe enough around the country :D I hope you sort the lights painlessly.

The switch is the same in all R32s, so swapping your bro's switch would be a cheap way to test it out. The switches are a well known cause for LH headlight failure. You can tell it is starting to go when you switch your lights on and only the RH comes on until you click on/off again or give it a hit Fonzie style.

As Deren said, good idea to check your fuses but I'd be surprised if any had blown.

Could you please report back when you've sussed it out?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      The Evolution Of "night Fury"

      By PranK · Posted

      Thats too fricken cool.
    • PranK
      Beers and skylines Fatz style

      By PranK · Posted

      That R31 was so cool. Only did Orange Park once. Scared the hell out of me.
    • GoHashiriya
      Volk TE37SL 9.5J +22 / 10J +20

      By GoHashiriya · Posted

      Selling my TE37SLs since I've switched to smaller wheels.  They're for sale in Japan but it's pretty simple to send them overseas; USA excluded, since JPPost isn't sending there at the moment. Specs Front: 18x9.5j +22 5x114 Rear: 18x10j +20 5x114 Price: 320,000 JPY/ 3,285 AUD (current FX rate) Condition: a few scratches here and there, no bends, distortions or cracks.  Tires will not be included for international buyers, I'll get them dismounted before shipping. They're currently listed on yahoo auction and will be shipped in Japan with the tires if they sell here. Shipping costs to Aus: EMS (1-2 weeks): AUD 1,175 (current FX rate) Sea (2 months): AUD 460  (current FX rate)
    • The Bogan
      NC MX5

      By The Bogan · Posted

      The alloy coolant reservoir has a sight glass, so as long as I can see coolant in the sight glass it's GTG, as for PS, it isn't anything catastrophic if it gets low, and as it hasn't lost a drop since I have owned the car I cannot see it being an issue, even after putting the "big block" 2.5 in....LOL The only time it gets slightly messy is at oil changes, as the oil filter sits above the frame, and I need to use a plastic bottle with its bottom cut off to catch the flow when loosening the filter
    • Duncan
      Single Turbo Conversion On R32 GTR.

      By Duncan · Posted

      Good on you for taking on the job, but it is a big one. Even if you have bolt on manifold and turbo, you will need: Post throttle pressure source to boost controller to wastegate (and FPR, and ECU/MAP sensor) Pre throttle pressure source to top of BOV(s) Oil feed - you can take that from the standard port in the middle of the block Oil return to block under the turbo - this is much trickier than it seems to route a decent/wide pipe past the manifold. You really can't use rubber hose because it is way too hot there, and also the oil out of the turbo core is a bit frothy so it needs to have a decent diameter Water feed - you can take that from the standard port in the rear of the block. Water return - mine runs to a T into the heater box return, just make sure you don't create a high point making bleeding hard. All of those lines should use 200 series style teflon braided hose with heat shielding because everything needs to be routed past the manifold. Also a turbo beanie is a really good idea to minimise the chance of the car catching fire (under bonnet lining in particular) You also need to decide a cam cover breathing solution as well, will you vent externally via a catch can (probably illegal) or return to the intake (plumbing required and can oil up everything over time) Keep in mind the intake and exhaust piping in the engine bay will be custom so you either need to be able to fab ally and steel or have someone you can get a car that isn't running to. Get the wideband fitting welded into the dump pipe at the same time. Also, just my opinion, a screamer pipe attracts attention and doesn't add power, I'd plumb it back if you want to be allowed to keep the car on the road. BTW do you know anything about how healthy the motor is, and what power you are targeting? Doubling or tripling the factory power on an unknown motor is a little risky. Also fuel system will need some attention (pumps, high current hanger, direct power and earth feed, injectors etc)
×
×
  • Create New...