Jump to content
SAU Community

Recommended Posts

Well just last night my car blew the front lower turbo coolant return hose(the small lower one on the front of the engine) and decided it would over heat on me but i caught it in time and i threw the clutch in and the car stalled completly as i rolled off the road.

The engine bay was covered in coolant but i was lucky and caught it early enough not to send the gauge to the red.

now we filled it back up with coolant and cleaned it off and the car runs fine until about 5 minutes after it has warmed up fully.

After the 5 or so minutes the car seems like the timing goes way off and sounds like a damn Tractor and full boost comes at 4500 instead of 3300.

Anyone able to give me some good ideas as to what it might be.

Thanks

Edited by icydude
Link to comment
https://www.sau.com.au/forums/topic/133658-r32-gtr-missing-once-warm/
Share on other sites

Once you loose coolant the guage wont read right as there is no coolant for the sender to measure. You have possibly overheated it enough to blow the head gasket. Tolerances change once warm so it might run fine until it heats up but then leaks after that. Try doing a compression test and a CO2 test on the cooling system to be sure.

Hope im wrong

Once you loose coolant the guage wont read right as there is no coolant for the sender to measure. You have possibly overheated it enough to blow the head gasket. Tolerances change once warm so it might run fine until it heats up but then leaks after that. Try doing a compression test and a CO2 test on the cooling system to be sure.

Hope im wrong

everything was good

just blew the fifth coil pack.

in addition i had 601 and 602 coils

they looked near the same but the 602's sucked

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Agreed, I've never seen a 260RS specific manual. As GTSBoy said it will mostly be stagea other than the engine loom https://www.hgeconsulting.com.au/stageaservicemanual.pdf
    • You'lll likely have to make do with R33 GTR for engine/tranny stuff, and Stagea for the body. I don't know that there's even been an actual diagram seen in the wild.
    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
×
×
  • Create New...