Jump to content
SAU Community

Recommended Posts

hey guys, whch exhaust should i get for my r34? i do not want a loud ass exhaust, i want something that flows very good and sounds good and isnt that loud,

i been quoted for a xforce 3` turbo back for $900 new

how is that compared with say jap exhausts?

any other recommendations?

most of it's going to come down to personal taste.

If all you want is a zorst to get the gas from the engine to out the back, then X-force is great value for money. Sure, the steel isn't as high quality, and the sound may seem 'tinny' to some, but hey, what does it matter, and for $900, turbo back, it's great value.

The other laternative is to get a bigger dump/front pipe (some in group buys) a high flow cat (ditto) and a jap cat back (pick your flavour... Apexi (or Apexera if you're being technical) HKS, Kakimoto......whatever)

The cost will be at least $300 for the pipe, about that again for the cat, and $900 for the cat back, which should include all gaskets.

So X-force will cost you $900, Something like an HKS silent will cost about $1500 if you import the cat back from nengun and buy the other bits on group buy.

Is the extra $600 (or so) worth it for a better sound, and better steel?

If so, go for it!

If not, well, you get the idea.

I went for the second option and got the HKS high power silent (though how an exhaust this loud can be called silent is open to question) and love it. I think the performance differences are negligable between different brands, provided they have the same width, and similiar straightness.

just pick your poison.

Look on Ebay you can get full stainless apexi systems for $1000. Go to the buy section and type in R34 or R33 heaps of shit there.

Edited by subzeroR33
lol most ebay stuff are fake tho

:D

Get one made up , that way you know what parts went into getting it done.

I have dumps HKS (2) ,3" High flow cat, 3' by aprox 1 foot Resinator and Hot dog X-force with Silencer.

I think with this I can stay under the radar. You can remove the silencer on the track.

All was made up for me with my steel choice :)

i have a 3` catback atm, but my rear muffler is only a 2.5` should i just get a hi flow cat and dump + front and a new muffler installed? but gettin these parts and fitted would set me back around 4-500 or i should just buy a the whole xforce system instead? bcoz i could easily sell my current catback for 500, that way i have a brand new exhaust system

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...