Jump to content
SAU Community

Recommended Posts

Hi All I have just had a mongoose M80 installed in my car. I got it installed with dual stage shock sensor and a glass breakage sensor.

I am not really hoppy with the place that installed it and do not have complete confidence in them.

The alarm goes off for no reason (while in my locked garage)

I took it back and they adjusted the sensors and it is still going off all the time.

Also they wanted a rediculous ammount of money to put an actuator in the drivers door so I decided I will do that bit myself. they did not even plug in the harness for central locking

so I have 2 questions.

1. do I need a master or slave actuator? the alarm has central locking relays already...

what are the wires I need to run to the door from the C/L loom and where can i buy an actuator?

2. how can I diagnose why the alarm is goin off all the time.

Thanks in advance :P

Link to comment
https://www.sau.com.au/forums/topic/134532-mongoose-m80-alarm/
Share on other sites

i got one of these installed into my car and i think the guys told me it was a master actuator that they needed to put in. they supplied and fitted it for i think it was $50.

with the other questions i dont have a clue to go about them

hope this helps

Stephen

master actuator. you will need to tie it to the lock switch in that door. ( the OEM one that drives teh other doors of the drivers door is usually stuffed!)

as for diagnosis : if yo uhave the book -read it. about 3/4 back there will be a few pageds on error chirps and led codes. that will tell you what is up. from there its up to you to adjust it.

fire me a PM with the alarm location (I'll help you hide it,)

when u disarm the alarm after its gone off the led should flash a combo which you can refer back to the manual to see which sensor is setting it off and thus make you adjustments. My bet is that your interior motion sensor is set with to bigger radius, if the interior sensor is tripped the alarm will go off without warning. try moving the motion sensor unit to very centre of the car to get best operation out of it, I have mine mounted in behind the handbreak but under the plastic so it cant be seen, however try to keep away from metals as much as possible as it effects the sensor. A warning to you if you mess with major functions of alarm you will void your warranty. Talk to baysidebluer34 from this forum he installs them and knows all there is to know bout them

My bet is that your interior motion sensor is set with to bigger radius, if the interior sensor is tripped the alarm will go off without warning.

He doesn't have the microwave sensor, only the impact sensor which should only go off if something bumps into the car and the vibration sets off the alarm.

I have this alarm and have had no troubles with it going off unwarranted, it's set on medium sensitivity for the Impact sensor...I'd be making sure yours is too.

when u disarm the alarm after its gone off the led should flash a combo which you can refer back to the manual to see which sensor is setting it off and thus make you adjustments. My bet is that your interior motion sensor is set with to bigger radius, if the interior sensor is tripped the alarm will go off without warning. try moving the motion sensor unit to very centre of the car to get best operation out of it, I have mine mounted in behind the handbreak but under the plastic so it cant be seen, however try to keep away from metals as much as possible as it effects the sensor. A warning to you if you mess with major functions of alarm you will void your warranty. Talk to baysidebluer34 from this forum he installs them and knows all there is to know bout them

true,

btw I fit these to all skylines and have been since 2001 so I figure I know them fairly well myself.

One other thing to consider is the type of sensor you are dealing with.

Is it a microwave or ultrasonic sender? Is it a pressure or vibration sensor? etc...

Basically microwave sensors emit a signal that can travel through glass, park the car in a tin shed and the signal travels out the glass hits the relective surface of the tin, is dispersed and may error the alarm.

Microwave sensors are generally un relialbe as they can also be tempreture dependant.

Ultrasonics emit a sound wave within the vehcile, the use a sender and a receiver and operate when the wave being sent is interupted. These are a lot more reliable, are not tempreture sensitive or prone to errors.

The other thing to consider is that if you are not happy with the way the system has been installed in the vehicle then take it somewhere else, tell them you bought the car with the alarm in it and then ask them for an opinion. You may be surprised at how crap the first companies instal was.

true,

btw I fit these to all skylines and have been since 2001 so I figure I know them fairly well myself.

Sorry Chris meant no disrespect to your knowledge or your abilities, its just that baysideblue did mine and got it spot on so only tryin to help a fellow member by referin him

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...