Jump to content
SAU Community

RPM Performance - Sat' 31st May Drag Day - post here if intending to enter


Recommended Posts

Sorry Matt take me off the list .... I haven't got any of my proposed mods done cos I've been too busy so there's no point running (since I ran a couple of weeks ago) .... will definitely be there though for a look!

  • Replies 111
  • Created
  • Last Reply

Top Posters In This Topic

Hey Matt :D

Can you update the first post with the following:

PAID

rob vu ss ute - Monaro CV8

BRUTE - VU SS

Remove the following

LS1-250 - VT HSV Senator

Hyper8 - VX SS

....and

HRT Stroker PAID

Jarrett - VT Senator HRT PAID (Jarrett may be above?)

are the same person.

Cheers

Mat

Yeah John (Munro) mentioned a few wks ago that Keir was going to run his car at this event. I've not heard anything more about it until now. Keir is welcome anytime as far as I'm concerned!

Matt,

I have 3 people paid up today.

Clint32 - R32 Skyline

Alexis Paul Poole Honda CRX

Rob VU SS - Monaro

Ben Siedel's RX3 RPM car.

I spoke to Mike Petrou to invite Keir Wilson with his GTR to the meet and Mike said that he will get back to me. Yeah, for sure, wouldnt mind seeing the 9.38 secs 32 on the track!!

Ivan will contact AIR today & find out about pit crew entry (in particular late arrival) takeaway food options & a few other details. He'll post the info up asap.

Keir Wilson will be running his GT-R :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...