Jump to content
SAU Community

Recommended Posts

Guest ONELOVE

Hi Guyz~

I just be a new member here.. Great site huh???

Ive got a R33 gts but wanna make it looks like a GTR..

I mean not bodykits.. things like GTR front & rear panels..

(I know it is worthless and better get a GTR instead but Ill never sell my car.. I realllllllllllly loveeeeeee it!!!!!!!!!)

I know some has done this (ex the red r33 from JMS)

Anyone know what is need to be done and the cost???

Any info would be appreciated!!!!!!

Thank you~!!!!!

Link to comment
https://www.sau.com.au/forums/topic/13565-gts-with-gtr-look/
Share on other sites

I think that u will find that u dont need to un pick the panel fromt hat far up. Im sure u would be able to cut the rear pumped sections out of a crashed gtr and put them in yours.

Id say u would only need to cut what 30 cm around the guard sort of thing as the rest could be "blended" by the crash shop doing it.

Link to comment
https://www.sau.com.au/forums/topic/13565-gts-with-gtr-look/#findComment-265442
Share on other sites

its a very big and expensive job and its not really worth it unless u hav a lottttttt of cash to spare. the front panels dont fit without a new bonnet and bumper too i think as the gtr frnt panels are a little higher at the front.. and gtr panels are alluminium too so theyre quite pricey......

Link to comment
https://www.sau.com.au/forums/topic/13565-gts-with-gtr-look/#findComment-265726
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...