Jump to content
SAU Community

Recommended Posts

Hi All,

New owner of a R33 which doesnt seem to have any reverse lights.

I understand there is no fuse and the fact that both lights are out probably means its not bulbs?

I was told that i should ensure that the switch going into the gearbox is correctly connected....havent had a chance to look, though can someone give me a heads up in terms of location of switch? ie drivers side, etc?

thanks!

Link to comment
https://www.sau.com.au/forums/topic/135942-no-reverse-lights/
Share on other sites

pretty sure the plugs are on the drivers side of the trans. if you get under the car you should be able to see. they are up at the top of the box. make sure the car is cold or you will find out just how hot the gearbox gets.

still work checking the bulbs though. it might turn out that there isn't any in there.

yep, check the bulbs since they are the easiest to get to.

the reverse and neutral switches are on the top of the gearbox, facing the drivers side. if you get under the back of the gearbox and look up and forwards along the drivers side of it you'll see 2 pairs of wires coming out.

the reversing switch is the furthest forward (hooray! it's a bitch to get to) and they certainly wear out - my reverse lights would only come on when i held the gear lever to the left whilst in reverse. I verified that it was really my gearbox switch at fault with a multimeter before bothering to change it.

you will probably have to lower the gearbox a little in order to change the switch, there's not much room to move otherwise. New switches are $50 from nissan, the plug on the end disassembles easily with a flat screwdriver leaving you 2 bare wires which will fit through a normal 19mm ring spanner. once you have the new switch in then re-assemble the switch (I don't have japanese hands either so it was fun).

thanks for the replies ppl......

yep kinks after playing around i found im having the exact same problem as you described (reverse lights turn on only when holding gear lever left).

Sounds like too much mucking around to get to it for my liking... easier with someone with a hoist!

Do Nissan have to special order the switch or do they stock them?

cheers

call your local and find out. mine stocked them.

I did it in the driveway, could be done just as easily if you had axle stands. If you have to lower the gearbox you need to get under it with a jack anyway.

it is a pain in the bum to get to but if I got to it in the driveway without even loosening the crossmember you can get to it without a hoist :ninja:

Thanks for the replies kinks..

how is the switch held on...screwed on??

is it worth trying to play with it before buying a replacement??

will have a look when i have a chance to jack it up in light...thanks for your help :ninja:

call your local and find out. mine stocked them.

I did it in the driveway, could be done just as easily if you had axle stands. If you have to lower the gearbox you need to get under it with a jack anyway.

it is a pain in the bum to get to but if I got to it in the driveway without even loosening the crossmember you can get to it without a hoist ;)

the switch is one unit with a thread on the front and wires coming out the back, it goes into your gearbox like a bolt would.

if you're familiar with a multimeter it should be straightforward to check the existing switch, if not then take a gamble and assume the switch is at fault :pirate:

Edited by Kinks
  • 2 years later...

Hi there, I hope someone can help. The part of the loom that connects to the reverse and neutral switches on my R32 GTS4 has been ripped out (one of those things). I can't see where these are meant to connect to; the best I can see is a bit of the loom that passes by the alternator but I can't be sure that this is it as these wires don't seem to activate my reverse lights. Any help would be great - I have a thread going about this here. Thanks, Ben

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
    • Should have taken that opportunity to slot in a twin scroll turbo setup. Maybe next time.
×
×
  • Create New...