Jump to content
SAU Community

Recommended Posts

A private day for Skylines is unobtainable. The wont reply to phone messages, emails or letters.

WSID is run by a bunch of people who only care about V8's and top fuelers.

That said, if we didn't own Skylines we could get a private day for $10,000 with a list of rules and requirements that are practically impossible to comply with.

Link to comment
https://www.sau.com.au/forums/topic/136227-wsid/page/2/#findComment-2533051
Share on other sites

  • Replies 78
  • Created
  • Last Reply

Top Posters In This Topic

A private day for Skylines is unobtainable. The wont reply to phone messages, emails or letters.

WSID is run by a bunch of people who only care about V8's and top fuelers.

That said, if we didn't own Skylines we could get a private day for $10,000 with a list of rules and requirements that are practically impossible to comply with.

Now now Adam, settle down champion. I'm sure that in a decade or two we'll be sweet with WSID. :O

Link to comment
https://www.sau.com.au/forums/topic/136227-wsid/page/2/#findComment-2533157
Share on other sites

But isnt there another drag place that can be used? or is WSID the only place? :O

not in nsw there isn't. or are you proposing we travel to another state/country for a drag day?

Link to comment
https://www.sau.com.au/forums/topic/136227-wsid/page/2/#findComment-2533353
Share on other sites

I was actually in talks with the guys there,

said needed 40-50 cars and around 200 each

no under 11 second cars.

but needed to be booked months and months in advance

Long story short, don't bother. At least not on our behalf. Seriously.

Link to comment
https://www.sau.com.au/forums/topic/136227-wsid/page/2/#findComment-2533480
Share on other sites

Congrats to Mr Dinzlr on the 11.0, 10.8 and 10.9 passes thats 1 top sounding GTR!

Well done, Din. ;)

What was the mph?

Oh, btw Baron, I know why Ben goes to every WSID event ever held....and her name's not Wendy ;)

Link to comment
https://www.sau.com.au/forums/topic/136227-wsid/page/2/#findComment-2540832
Share on other sites

128, 128, 132.5mph from memory.

Mik got down to 11.2sec @ 128mph also from memory and afew GTS-t's from here doing 14's. Also Caz in the 300ZX did a mid-low 13sec in amongst all the other 300's out there.

No her name definitely isn't Wendy although she still melts in my hands.. ;)

Link to comment
https://www.sau.com.au/forums/topic/136227-wsid/page/2/#findComment-2540841
Share on other sites




  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...