Jump to content
SAU Community

For All Those Who Ever Had Back Fire, Idle And Aac Valve Problems


Recommended Posts

HI ALL

Well here it is, after spending countless hours reading and trying everyhting, nothing would cure my backfire and the fact that i could not set the engine idle with the TP off lower then 900 rpm. Cleaned my AAC Valve, tested for leaks ect ect. You name it i tried it.

IT turns out the culpret was the Air Regulator, the one mounted below the intake plenum. Mine was simply not closing fully, it would simply not allow the orfice to close. So air always entered the car, enough to make a differance.

I took mine apart, being very carfull, a whole heap of stuff inside, and cleaned everything with carb cleaner, and problem solved.

The air regulator is an absolute pain in the ASSSSS to get to, here is the pic for R33 and R32.

I recomend everyone tries this and see if their problem goes away.

If it helps others i can do a write up on what needs to be done to get it off.

To test each one, simply plug up a battery to the terminals and after 7 minuts the orfice should be closed.

Good luck all, my problems have gone away, well have other problems but one down. LOL

Air_Regulator_R32_GTST.pdf

Air_Regulator_R33_GTST.pdf

Air_reg_Test_R33.pdf

Top stuff matey, I didnt know it exsisted, just how hard are they to get out?

A write up on cleaning it would be very helpful, I have a feeling this is a culprit that has gone unnoticed.

I will take some pics on the weekend, and do a write up then. It's noo to bad, but i found it was easier to acces from the bottom, from memory, there is only one bolt to get to, the hardest thing is removing the hose clamps.

Basicaly, if you've cleaned your AAC valve and nothing, then this is the next thing in line, i found mine was bugared simply because my rpm idle set procedure do not sit below 900 rpm.

Inside ther is some springs and a diaphram, not to bad, but you don't have to take it appart, if you spray carbon cleaner into it and so forth it will remove 90% of the problem.

Edited by WogsRus
  • 1 month later...

I couldn't be stuffed with mine, so I just blocked the hose off with a bolt for now till I can be bothered getting to it...

One downside, on cold starts you need to warm up the car before it's driveable, but summer is here now so I'll do it at the end of summer.. haha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yeop... binned it   This will be a summary will not many pics atm and cbf  Fixed the samsonas - it was totally munched Put a new precision 7675 T4 on with proper split pulse mani Got to Sydney to get to car - drove to canberra to get racecar - drive back to sydney that night Next day all day at Plasmaman putting on new clamps cleaning some things up and adding another large engine oil cooler sitting at the rear above diffuser to keep things cooler Next day - Tuesday - on Dyno - killer wikid awesome pumped out really good numbers - more mid range and on lower boost levels Wednesday - first prac - all day again getting the suspension right - had to borrow front suspension again - out do a lap come in - out do a lap - in - what i had just couldnt handle the load at the more consistent higher speeds - got a lap in at the end of the day that was pretty reasonable  Put it this way that lap wouldve had me in 4th in Pro am for the whole event - with only 700 hp and used tyres Thurs first official prac day - lap out warm up - with above setting and 80% effort took corners 1,2,3 and into 4 car felt awesome -  rear came around out of nowhere bang into the wall near front on at whatever 140 kmph Done, over, gone Just one of those how did that happen apparently as all indications show nothing out of the ordinary Got to spend the rest of the time at the event like I hadnt done before - was actually Ok mainly as I had my family and my boy is 9 and got treated like a rockstar Long trip home, lost a trailer wheel in nowhere land, X5 airbag suspension gave up half way across nullabour and rode on bumps stops (its now completely fine) had to do a 19 hr drive day on day 3 as accommodation got screwed up so just had to keep driving till found a town with some Now to reassess - hopefully the motor and other things are OK but yet to be seen too. There is no easy fix there is no i'll just order that part and get it sent - we'll have a talk to people see what can happen and what the go is but at minimum its rebuild from scratch struts forward and alot of time effort and $ should and if I return and if but maybe/ when  I have the cage tied into the front strut towers - if I didnt have that things couldnt been worse you can say its just a front end but if you know what goes into these cars... you'll know what that actually means in reality   Car was very fast. Disappointing we just didnt get to show it Effort doesnt win you races though     Apparently this is motorsport !  
    • Thanks, will do that.  Thankfully they still feel great.
    • Yeah man, absolutely. You can try pushing me all the way in swapping the R34 for an E9x M3 
    • It's almost certainly going to be some amount of pads compound transfer onto the rotors. It will probably go away after you've run them for a bit. If not, pull it all out, lightly sand the rotors, scuff the pads, and rebed.
    • no one recommending speedtek gearsets?   i'm in the same boat as Cosline but rwd, I am holding boost back in third to 600nm at the hubs to save the gear as i make nearly 750nm at the hubs on a mainline
×
×
  • Create New...