Jump to content
SAU Community

Recommended Posts

hi guys

just wondering what other dyno results are around on 34's.

Thes are my mods:

Full 3.5" kakimoto exhaust

A-vcr boosted @ 1 bar

Power FC

Front mount intercooler

i had problems with this mechanic but the car feels ok.

Should i get it dynoed/tuned again or is this result ok for these mods.

before i had the Power fc and FMIC tune i ran the car and got a 13.6@ 101mph but i was only running .85 bar(12psi)

cheers

steve

Link to comment
https://www.sau.com.au/forums/topic/138462-1869rwkw-1bar-on-my-r34/
Share on other sites

Sounds a little low given you're running 1bar, but if we could get a look at your dyno sheet that would be great.

btw.. that's on the stock turbo? just that 1 bar on the stock 34 turbo seems a little excessive.

yeah its the stock turbo. thats my point ive been reading everywhere that we shouldnt boost it to 1 bar all the time, but the mechanic that tuned it said it would be fine. ive been running it constantly at 1 bar and it seems fine.

Sounds fine to me. Remember a dyno is just a tuning tool/indicator.

Obviously time to time there are extremely bogus readings...

But i usually allow a 15rwkw variance for any given dyno on any given day and then you'll find most results fit into that variance.

But 190rwkw is pretty much spot on dude.

Some dyno's will have your car around 200, some 190, some possibly 180.

If the power graph is smooth, car feels/drives well... thats what really matters.

Although i wouldnt run 1bar... turbo isnt going to like that forever.

  • 1 month later...

mate....that sounds real low........mate of mine gets 181rwkws with just .7 bar of boost and a exhaust and thats with no cooler.....get it retuned

Edited by anDru

As 'R31Nismoid' says, allow for +-15rwkw variance on different dyno's. There are that many variables that can affect the power output (Tyre size, wheel spin, dyno calibration etc.) and if you had issues with your mechanic he's probably tuned it rich just to be safe. Did your mechanic use FC datalogit to tune the PFC or just the hand controller?

To me that sounds spot on mate, I'm personally expecting 175-185rwkw with turbo back, pod and 10psi.

EDIT: Just read 1 bar, but even then I'd say its pretty spot on. After 12psi the stock R34 turbo apparently is just blowing hot air so I'd crank that down to 12psi max mate.

Edited by Andi
mate....that sounds real low........mate of mine gets 181rwkws with just .7 bar of boost and a exhaust and thats with no cooler.....get it retuned

retuned? why?

Did you mate have his car dyno'd....

on the same dyno?

at the same time?

on the same day?

If you answered NO to any of the above three, then you have absolutely no claim to say its wrong, or it needs a retune.

anDru, you really need to think before hitting the submit post button.

190's is wots to be expected realistically.

My 34 - Power FC, turboback, FMIC, BC kit - 194rwkw at 14psi. That was during the tune, i dont run it anymore than 13psi. Like most have said turbo is just out of efficiency after that.

retuned? why?

Did you mate have his car dyno'd....

on the same dyno?

at the same time?

on the same day?

If you answered NO to any of the above three, then you have absolutely no claim to say its wrong, or it needs a retune.

anDru, you really need to think before hitting the submit post button.

mate that is a HUGE difference and not some 15kws u said.....compared to my mate...and i no there might be some diff with not the same dyno and not the same day blah blah but can a car seriously be losing around 20-30 kws just from that?

::EDIT::

i just gave my mate a call (he got his car dynoed again) and his achieving 200 rwkws with .85 bar, FMIC, and a standard 3" turbo back

i dunno man but "tough r34s" dosnt sound so good

Edited by anDru

My mate has a R34 with

HKS2530

dump-back exhaust

fmic

pfc -tuned at CHASERS

GFB bleed valve

spitfire coilpacks

made 207rwkw at 12psi but i suppose its got more in it.

My R33 has an safc, dump back zorst, fmic at 12psi it made 211.2rwkw.

If i were you take it to C&D Motorworks in Braybrook (Melbourne) for a re-tune.

A later model skyline with a Neo motor should at least reach the 195-205rwkw zone.

Diagnose your engine for any possible problems that may be preventing your engine from producing its actual power reading.

nah nah nabil r31nismoid said we all should think before we post about how a r34 should run......

because we are all stupid because we believe a fellow r34-ers car isnt running as good as it should

hehe he just said YOU need to ;)

nah nah nabil r31nismoid said we all should think before we post about how a r34 should run......

because we are all stupid because we believe a fellow r34-ers car isnt running as good as it should

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...