Jump to content
SAU Community

Recommended Posts

Abo, check out the type of catch can that you can open with the allen keys. not just the ricer chrome ones that are just for look.

You can actually fill it with steel wool and they work great. I just sold a spare one I had. The one in my car is awesome.

It's 1L. That's plenty big enough, doesn't take up too much room etc.

Hi Adam - Can you please let me know where you end up getting the sheets from?

I'm looking for some now, but alot thinner.

I might check out the place B-man suggested, but I only need a small amount, say 1m².

Cheers

Liz.

Liz we have 2x 1.2mm sheets as well if you need some... about $25 for 1/3 of a sheet

Cheers Duncan - When I get the car back I'll measure up and find out exactly how much i need and give you a bell.

Penrith across the road from HITMAN

but live 2mins from WSID(doonside)

what sizes do you need?

we have a guillotine,i can cut them for you.

Hi Dean1285, i purchase my companies steel & ally from smorgon

give me a discount.lol

Penrith across the road from HITMAN

but live 2mins from WSID(doonside)

what sizes do you need?

we have a guillotine,i can cut them for you.

Hi Dean1285, i purchase my companies steel & ally from smorgon

give me a discount.lol

You're a champion.

I need:

280x155mm (x2)

280x50mm (x2)

180x155mm

50x161mm (x2)

Sending a pm too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...