Jump to content
SAU Community

Recommended Posts

mmm

gf rekons fresh coat of black with some rainbow flake in it

im tossing up gunmetallic grey with heavy rainbow flake... or my gfs mazda chocolate metallic brown (still have 2L of paint left from her car so...)

front wheelbearings i believe are my noise/vibration in the front so need to get them done this week

just need to wait till tomorrow to ring around for bearing prices

front 18's arrive this week to complete the set (yay)

however my gf just bought some 18x9 +15 and 18x9.5 +12 bronze TE37's... and she wants my wheels so... im unsure wether to swap her or not...

18x10.5 +26 with 8mm floater and -1 camber with 215/40/r18 stretched

guard rolling done by my gf

guards getting fixed in about 2 months and being pulled out another 10-20mm... ideally i want to run 18x9 +0 front and 18x10 +0 rear comfortably i can fit an 18x10 +10 without spacer with the lip of the rim exposed by guard edge (what i consider flush)

LOL

dude i got about 30mm of pull so far

factory untouched guards you can roll on 9jj +30's all round with some stretch... ceffies dont accomodate shit

do i have pull? oh i got pull! it aint pretty but its pull!

post-25224-1170938380.jpg

man i wish my girlfriend had similar .. or even remote interest in cars and taste in wheels with offsets like that.

tuff looking ceffy though dude.... ur always turning out DISH on your cars.. im jealous.

good luck with it.

well i test fit te37s tomorrow... oh yesh pics will be supplied :no:

both on her s15 and on my a31... so... d day tomorrow

kinda turned off by dish... although later on this year ill be getting an s14 shell to do as a long term track project... looking to squeez 18x11 -20 under the rears :P or something like that

**WARNING** NO 1" POLISHED LIP CLASSIFIED AS DISH QUOTED WITHIN BY THIS USER

Edited by Hella Flush
LOL

dude i got about 30mm of pull so far

factory untouched guards you can roll on 9jj +30's all round with some stretch... ceffies dont accomodate shit

do i have pull? oh i got pull! it aint pretty but its pull!

:( wats da measurements of dat rim in dat pic in da rear guards?

in the bottom one? LOL

16x7.5 +45 hahahaha

SUNKEN TO THE MAX

my 10.5 +26's are much better fitting but still in a tiny bit

haha yea ... sunken!!!! :happy: ...lol

Edited by Dan_J
  • 2 weeks later...
  • 8 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...