Jump to content
SAU Community

Recommended Posts

I had my air filter mounted in the front gaurd right infront of the front bar for cold air flow and i have noticed issues when driving over 70ks an hour in top gear the engine would cough and pop and miss all the time especially at over 110ks an hour.

I just upgraded my air filter to a Apexi power intake model which must flow much more then the other ones i was using (long story) and noticed the issue got worse - then i realised it could be air being forced into the filter and going straight past the AFM.. so air was being forced through the afm and the engine does not need to use it.... (kinda like a boost effect through the air filter intake pipe)

So this morning i put a piece of cardboard and covered the gap on the front bar and the drive to work was nice and smooth - perfect as a matter of fact. no missing or coughing or spluttering and the PFC was showing around 3 - 4 less % injector duty.

Going down a big hill i turned the engine off and turned the computer on and the AFM was measuring about 1800 - 2200mv at 110ks an hour with the engine OFF (before i blocked the air flow) - at idle it sits at 1050 - 1100mv - have not done a test after the air flow was blocked yet...

So causing a ram effect on the air filter for cold air feed can cause issues....

I am going to build a box in the front gaurd / front bar and enclose the air filter .. if that dont work i will have to move the AFM to the boost pipe.

Just wanted to share this :)

Alot of people have always said this would be a problem, its good to have some proof.

Also, you turned your engine off at 110km/h? Thats brave... no power steering etc.

Alot of people have always said this would be a problem, its good to have some proof.

Also, you turned your engine off at 110km/h? Thats brave... no power steering etc.

yeah its a big hill.. goes for about a km and its three lanes wide... was just a test!!

^^ Is that sarcasm?

But yeah any direct airflow I've found results in unstable readings for the AFM due to turbulence. Ie cruising at 60kmh the voltage will be +- 50mV. Do the same at idle by raising the RPM to 2000rpm and its pretty much steady (+-10mV)

EDIT - forgot to mention the above was with a CAI feed from the front with a 3" hose.

Edited by Busky2k

Noticed this on the Dyno at Dr. Drift with my CAI

- had to reposition the DynoFAN to stop it causing problems.

Never considered the on road effects before.....

hahaha SK. what the ? the air is only going one way.. its just being rammed in ;)

OK, either you are having a dumb day or I didn't explain it very well. I will assume its my fault and have another go.

What is happeing is the air is being rammed in

1. through the filter

2. into the inlet pipework

3. through the AFM

4. through some more inlet pipework

5. into the compressor

6. the compressor "rejects" what it doesn't need

7. some of this air goes back out through the AFM (ie, gets measured twice)

8. this is air that the AFM has measured (once and/or twice) but it hasn't gone into the engine

9. so the ECU is squirting in more fuel than the engine needs

So what you need to do is stop that reverse airflow. You do that by sticking a one way valve in the inlet pipework (#4 above) between the AFM and the compressor. When the compressor is using all of the airflow, there is no pressure build up, so the valve stays closed. When the compressor is rejecting some air flow, there is pressure build up, which opens the one way valve. A simple PCV valve works OK.

We bleed off pressure from the airbox on N/A race cars (even V8 Supercars) for exactly the same reason.

Does that make sense now?

:wave: cheers :)

what sk is talking about is basically a pressure valve. it is kind of like the pressure valve in a hot water system, or pressure cooker. when the pressure gets to a certain point the extra air will go from inside the plenum, out the valve, and into the engine bay.

could it possibly also be your plugs? what gap, how old, etc are they. if the extra air is getting into the motor it could be blowing your spark out.

Edited by mad082

I never considered that the air could be rejected by the gt35r compressor... Interesting.. i think in this case because the AFM is connected straight onto the air filter sitting right in the front bar the air is just being rammed through the AFM and telling the computer that it using more air then it needs...

On my AFM it is connected to a 4" pipe which feeds up into the engine bay and then onto the compressor housing - probly around 70 - 80 cm of piping or more by the time it hits the compressor - i assumed it would just compress not surge back down the pipe.

Can you get a 4" pcv valve ? where would you get it from??

If i enclosed the Air filter / AFM in a aluminium enclosure and had a smaller entry to the box so air does not directly hit the air filter would that fix the issue as well as the pcv valve?

OK, either you are having a dumb day or I didn't explain it very well. I will assume its my fault and have another go.

What is happeing is the air is being rammed in

1. through the filter

2. into the inlet pipework

3. through the AFM

4. through some more inlet pipework

5. into the compressor

6. the compressor "rejects" what it doesn't need

7. some of this air goes back out through the AFM (ie, gets measured twice)

8. this is air that the AFM has measured (once and/or twice) but it hasn't gone into the engine

9. so the ECU is squirting in more fuel than the engine needs

So what you need to do is stop that reverse airflow. You do that by sticking a one way valve in the inlet pipework (#4 above) between the AFM and the compressor. When the compressor is using all of the airflow, there is no pressure build up, so the valve stays closed. When the compressor is rejecting some air flow, there is pressure build up, which opens the one way valve. A simple PCV valve works OK.

We bleed off pressure from the airbox on N/A race cars (even V8 Supercars) for exactly the same reason.

Does that make sense now?

:wave: cheers :)

Well if i did that then the AFM would be reading air that would be escaping from the valve which would make the engine run rich. Yes ?

I use copper plugs and change them every 2 months. i run .7 .8 gap.

what sk is talking about is basically a pressure valve. it is kind of like the pressure valve in a hot water system, or pressure cooker. when the pressure gets to a certain point the extra air will go from inside the plenum, out the valve, and into the engine bay.

could it possibly also be your plugs? what gap, how old, etc are they. if the extra air is getting into the motor it could be blowing your spark out.

Well if i did that then the AFM would be reading air that would be escaping from the valve which would make the engine run rich. Yes ?

Yes, but it would stop the AFM "reading" the air flow twice, which is what is happening now.

Plus it sounds like you have the AFM located in the rammed air tubulence. It may be worthwhile moving the AFM a bit further away from the filter. I understand why you have it as far from the compressor, it helps with any reversion problems. But somewhere in between might be beneficial. At least it would move the AFM out of the turbulance and it would be getting only straightened airflow.

:wave: cheers :)

i had my pod mounted directly in front of my left front wheel where standard intercooler used to be for a few years, well, it was right behind a vent in the front bar

never had any issues with it at all

only removed it coz the pod would get so dirty, especially in the wet

Edited by Spook's_Skyline

i think rather then moving the AFM (unless i move it to the boost pipe on other side of engine bay) i will just enclose the filter and and afm away from the direct air flow.

I've wondered the same Guilt-Toy. Even tho i dont have a cold air intake i have noticed when backing off light throttle the afm volts go back and forth higher then before i backed off LOL. When it does and i change gears it wants to stall, pisses me off.

I think i might get rid of the PFC as it's shitting me.

Interesting indeed’ally, iv been playing around with how im going to make a CAI for a BNR32 running a single turbo and twin AFM’s.

I’ll be pushing most of the air that goes into the passenger side front bar vent into a effectively sealed box containing the filters. My thinking gets me as far as, if it’s the speed of the air going into the vent, that creates a higher then normal (read, higher then the car was tuned) pressure at the turbo mouth then I could as easily vent air off at the air box. I reckon a large 250x250mm spring load flap, on top of the CAI would relieve enough air at higher vehicles speeds to prevent the pressure spike AFM double reado thingo. Seems safer then one way valve, introduces another possible fail point.

All this, and a cossie bonnet vent over the CAI, (mounted the right way :0 ) that seals hard against the bonnet might do.

I guess I could record AFM outputs, injector times, some air box pressure readings, switch on the flap lid cross match vehicle speeds blah blah and write a super nerdy write up… but could one be f*ked  Hahahaha

- M

Edited by GeeTR

thats a interesting idea.. i am just going to make it so air can go in and out of the box easily so its allways got fresh air in it and have the air filter sitting below the air flow

so if I'm reading correctly too much air ramed in is not doing you any good.

I setup a box over the pod and AFM and took away the stock intake. I used a 3" pipe from the grill which comes in under the pod - using the stock IC hole..I havn't noticed any issues... I would assume this setup is basically the same as stock with more air and a more direct flow into the CAI area however the differnece is that its not in direct airflow at the bar...yet I would assume the 3" pipe would allow a lot of air to get in...maybe its enough of a baffle to avoid the issues being discovered.

Its not totally sealed...it has gaps on the sides..I never worried as I assumed so much air was getting in there it would keep away the hot engine air...after all that was the aim of the box...I wont bother to seal it up perfectly then

Myabe you don't need such a good flowing filter under such circumstances...as you have so much air its not really a flow issue. I have been using a UniFilter which has less flow than the pod mentioned but filters much better...just another thing to consider IMO...

Thats what i was thinking.. a box that is not sealed so it can get cold air as well as not have so much pressure at the same time.

See how it goes at the moment the piece of cardboard is working wonders :dry:

so if I'm reading correctly too much air ramed in is not doing you any good.

I setup a box over the pod and AFM and took away the stock intake. I used a 3" pipe from the grill which comes in under the pod - using the stock IC hole..I havn't noticed any issues... I would assume this setup is basically the same as stock with more air and a more direct flow into the CAI area however the differnece is that its not in direct airflow at the bar...yet I would assume the 3" pipe would allow a lot of air to get in...maybe its enough of a baffle to avoid the issues being discovered.

Its not totally sealed...it has gaps on the sides..I never worried as I assumed so much air was getting in there it would keep away the hot engine air...after all that was the aim of the box...I wont bother to seal it up perfectly then

Myabe you don't need such a good flowing filter under such circumstances...as you have so much air its not really a flow issue. I have been using a UniFilter which has less flow than the pod mentioned but filters much better...just another thing to consider IMO...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
×
×
  • Create New...