Jump to content
SAU Community

Cant Find This Cf Bonnet For R33s.....where To Get?

nsta

By nsta,
in Exterior & Interior Styling

 Share

Recommended Posts

Logikal Collaborator

Logikal

Posted
Posted

hi nsta,

been looking at something similar myself.

closest bonnet that looks like that is the one from powerplay imports. it's an east bear item - 400R style bonnet

http://www.powerplayimports.com/images/par...S1c-bon-300.jpg

Bit expensive at $2052 though :P but hey thats what you get for good quality CF parts!

Dirty32 Collaborator

Dirty32

Posted
Posted

MrVspec... That looks good mate...

Looks really strong if you could call it that and less tacky than a lot of other carbon bonnets iv seen.

Do you sell bonnets for 32 gtr's???

Once again looks good.

Noy Experienced

Noy

Posted
Posted
MrVspec... That looks good mate...

Looks really strong if you could call it that and less tacky than a lot of other carbon bonnets iv seen.

Do you sell bonnets for 32 gtr's???

Once again looks good.

yeah we do bonnets for 32 GTR's squizz has one on his GTR.... we do an OEM or a vented one as seen on ON EDGE GTR..

MrVspec... I HATE YOU

Haha nice job, wish my CF attempts were of that quality.

Nice wide weave too, looks hot

do you make parts to sell?

yeah well i work for Custom Carbon here in brissy, we sell all sorts of items... i'm just getting a list together and trying to get the boss into gear to sign up on here... we do alot of 1 off custom work too..

i'm working on alot of drag stuff too... will post up pics of stuff as i go along..

  • 1 month later...
jroam Rookie

jroam

Posted
Posted (edited)
yeah we do bonnets for 32 GTR's squizz has one on his GTR.... we do an OEM or a vented one as seen on ON EDGE GTR..

yeah well i work for Custom Carbon here in brissy, we sell all sorts of items... i'm just getting a list together and trying to get the boss into gear to sign up on here... we do alot of 1 off custom work too..

i'm working on alot of drag stuff too... will post up pics of stuff as i go along..

MrVspec how much would a CF bonnet like yours go for????? ;)

Edited by jroam
Noy Experienced

Noy

Posted
Posted
MrVspec how much would a CF bonnet like yours go for????? :huh:

we cant supply them at the moment, can't get carbon wide enough to make them, but a bonnet just like mine will set you back around $3500Inc GST

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...