Jump to content
SAU Community

Recommended Posts

Hey ladz, ever since i put my aftermarket wheel on with a HICAS boss kit the warning light has been coming on after about 8 mins of highway driving..

i had the Wheels aligned today and the steering wheel is on PERFECTLY STRAIGHT... i also had some nissan mechanics look at it and check it over and its all A OK. they also ran a diagnostic with a result of NO FAULTS

but the bloody light still comes on... and it drives perfectly..

how can i stop the light from coming on, its very worrying to see it on when i drive, but i know nothing is wrong.

There is a fuse box in the boot with Hicas on one of the fuses... what happens if i simply remove this?

what other way can i stop this bloody light from coming on when nothing is wrong

Drill a small hole in teh dash and unscrew or break the bulb?

i know that sounds silly but i dont want to see the bloody thing, its annoying... especially when i know everything is fine..

Beef

Link to comment
https://www.sau.com.au/forums/topic/139398-hicas-warning-light/
Share on other sites

First remove the gauge surround then remove the actual guages and all you have to do is find the right bulb and twist it 90 degrees then pull it out.However i wouldnt rest till i found the reason for the bulb being on. Has to be a cause. Mine does the same however i havent driven the car for over 12 months so im yet to fix it. I have done the same as far as the boss kit goes. The workshop manual outlines the diagnostic procedure for HICAS. Dont trust anyone, thats my motto..

Deren you've probably got the wrong boss kit. There are two for the R32, ON-110 and ON-115. One is for early model cars like ours (pretty sure it is the ON-110) and the other is for late 92-onwards (or something like that) and says SUPERHICAS on the side of the box. The lugs are in different places. I think ours is 2 and 7 o clock, later models were 12 and 6. Might be the other way around, haven't had the wheel off in a while.

And for the other guys, Beef said he is using a boss kit, not a HICAS lock bar. I think we all get the big difference. Using a boss kit shouldn't mean taking out the HICAS globe. Beef you may also be using the wrong boss.

Hmm hope not as i doubt they would exchange it over 12 months later lol...Thanks for that though Mark. Could you take a look at your to tell me which I should have? Only if its not too much hassle to find out.. Might try google now, see if there is a HKB site

on r32 its the green one with the white trace wire. bottom left hand corner of the smaller of the 2 wiring looms on the hicas computer.

dunno on R33, but get your hicas computer, pull the wiring out and then use a short piece of wire connecting each pin on the harness to its respective pin on the the computer until you find the one that turns the light on. once you've found it, cut that wire

thats what i did on R32 anyway, dont think it would've changed dramatically for R33

give it a go

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...