Jump to content
SAU Community

Recommended Posts

heh u noticed that too eh?

A mates 32 has all 4 that lights up and only 2 do on mine. I agrree - A little info from some1 would be great.

btw 32godzilla is that your car on your avatar? Its hot! What sorta front skirt extension/front bar have u got on it??

My understanding is that correctly complied cars (ie no shortcuts) only light up two outside tail lights with parkers, and when you brake all four light up.

My car lights up all four with parkers/headlights, and when i brake they simply glow brighter. Ok so my car wasnt complied properly... so what.

... and in case a complier chooses to attack me for providing misinformation about the industry, this is what has been said about my car.

Shortcuts isnt necessarily the reason. I spoke to my compliancer about this very issue. He said the paperwork he recieves from canberra sometimes has it listed, sometimes it doesnt. A compliancer will only do what is listed as a requirement.

Apparently the ADR papers vary not only in years of production but in MONTHS of production too. Its very strange.

Red17

My b/f got told when he got his GTR that in compliance two of the lights are disconnected/cut as when you look an an Aussie delivered 32 GTR, their indicators and reverse lights are different to the imported version, i.e An import's indicators are where an Aussie delivered's reverse lights are, apparently.

It easy just to re-solder the wires back together, then you'll have all 4 light up.

Thanks for the info people, I'll have a look for any "cut" wires and post another reply as soon as I find anything. Four lights look better lit up than two i reckon - that's all. (like the 33's)

deorbit, not sure what front lip I've got as it came with the car, and to be honest never realised until about 2 weeks ago when I checked out another 32 GTR!

  • 2 weeks later...

I finally had a look the other day and yes there was a green wire in each light cut, just crimped them back together and 4 lights.

Prank, that sounds about right but why then do R31 Skylines have the same set up i.e. 5 brake lights and parker lights??

I have heard that they disconnect the outside two tail lights because there is an ADR that says something about the indicators are not allowed to be in board of any tail lights....hence the disconnection.... Also explains why Nissan rearranged the light configuration on the Aus-spec GTR's.

But as you have found out, piece of piss to reconnect :P:P

The ADR rules say that you need to disable the park lights on an R32 GTR, but as for R32 GTSt, there's no such rule as yeah, there is a center brake light. If you were to remove this, I'm told you can dicked by the cops for having all 4 afterburners active. But I've never heard of this ever happening so muh.

Lol I've got a spoiler brake light AND my SKYLINE lights up too (factory option)... now if I can get a replacement bulb and be bothered putting it in then yeah I'd be driving with 6 brake lights lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...