Jump to content
SAU Community

Stubborn Brake Dust On Chrome Part Of Rim

nuffsaid

By nuffsaid,
in Exterior & Interior Styling

 Share

Recommended Posts

nuffsaid Veteran

nuffsaid

Posted
Posted (edited)

Hi all

My current rims have a chrome lip, and due to brake dust there has been some slight tarnishing/patchiness/staining and build up of guk on the bits of the chrome.

I can kinda scratch it off with my finger nails, and in some sections, it just looks a bit tarnished.

Tried some light polish, some meguiars products, nothing can get it off.

I am guessing its due to the brake dust because the rear wheels are completely fine, just the front rims.

It kinda looks like water marks and is not as smooth when you run your finger over the chrome lip.

Any suggestions on what I can do?

Thanks all

Edited by nuffsaid
VAGABOND Newbie

VAGABOND

Posted
Posted

i read somewhere about this. there really isnt anything you can do apart from getting your rims resprayed to look like new again. the best thing to do is when you have new rims is regularly clean them because its the dirt and brake dust that damages them

SKY031 Grand Master

SKY031

Posted
Posted

metho will remove the staining, but if you want to give it a go, be EXTREMELY careful and make sure you don't get any on the tyres. Put the metho on a rag, apply it directly to the stained areas and rub.

*Disclaimer: If your tyres melt, i won't take responsibility for it! :thumbsup:

If you want to try something a bit safer, have a go with some autosol.

SKY031 Grand Master

SKY031

Posted
Posted

if it's chrome, spirits shouldn't dull the finish, if you're scared of scratches, make sure you get any surface grit off first.

If you have the slightest concern about using spirits near the rubber, then try autosol first

if you can't find autosol (or don't want to spend money on something that might not work) go and raid the kitchen.

vinegar and bicarb is a very user friendly (and enviro friendly) combination for any cleaning task!

N1GTR Grand Master

N1GTR

Posted
Posted

Pics of before and after?

I have this problem with one of my sets, the worst part is, the national electroplating union says no one in Oz does car wheel dipping, heaps do trucks, but none to car rims....

nuffsaid Veteran

nuffsaid

Posted
  • Author
Posted

I put some Meguiars paint cleaner on it yesterday and rubbed the hell out of it with a terry towel. Seems to have cleared up most of the problem.

Also scratched off the really stubborn bits with my finger nail heheh

Anyone have any other good tricks?

Marsss Grand Master

Marsss

Posted
Posted

depending on the type of chrome you have.. if it's not high quality take care not to use any abrasive products like Autosol or cutting creams... at this stage you'll need lots of elbow grease and WINDEX... and use a cotton cloth like an old T-shirt.

nuffsaid Veteran

nuffsaid

Posted
  • Author
Posted

Yeah I think I may have already slightly scratched it, its not really noticeable anyway so I am not too fussed.

I waxed the chrome part of the rim so that the brake dust should come off easier next time.

Alot of elbow grease went into it last nite, most of it seemed to have come off.

The chrome feels very plastic-ky though, not like solid metal. seems as if there is a clearcoat on them

Marsss Grand Master

Marsss

Posted
Posted

my point exactly..try not to let the dust build up...if it's black dust maybe you should consider changing your brake pads to Bendix Ultimates as the dust is "white" and not as harsh on chrome.

nuffsaid Veteran

nuffsaid

Posted
  • Author
Posted

Its brown dust, that usually, if i wash my wheels once a week, comes off really easily. Problem is this time I left it on to bake too long.

My Formula Ferodo pads are just way too dusty for me, maybe on par with Ultimates, but they give off a brownish dust which is the adhesive compound in the pad material moreso than metal filings.

I have given up on finding performance pads with low dust, i think its like asking for good tyres that last a long time.

SKY031 Grand Master

SKY031

Posted
Posted
the national electroplating union says no one in Oz does car wheel dipping, heaps do trucks, but none to car rims....

Many mag manufacturers have total control over their products, which means that some multi piece rims can't be disassembled by anyone other than the manufacturer.

If this is the case with the brand mags that you have, the only option is to send them back to the manufacturer for repair/restoration work.

However, unless the finish on the plating has somehow been compromised, they wouldn't need to be re-plated.

There are heaps of places that specialise in mag wheel polishing/restoration, but after having a quick look, I couldn't find any local to you. :)

N1GTR Grand Master

N1GTR

Posted
Posted
Many mag manufacturers have total control over their products, which means that some multi piece rims can't be disassembled by anyone other than the manufacturer.

If this is the case with the brand mags that you have, the only option is to send them back to the manufacturer for repair/restoration work.

However, unless the finish on the plating has somehow been compromised, they wouldn't need to be re-plated.

There are heaps of places that specialise in mag wheel polishing/restoration, but after having a quick look, I couldn't find any local to you. :)

Thanks for that mate ;)

yeah i spent a day ringing every place in Australia, no one will do them back to how they are now :O

All i can do for them, is have them polished and the middles sprayed with black (powdercoat), but thats a fair bit of hassle, i think its time for them to go

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...