Jump to content
SAU Community

Recommended Posts

i got a rb25det and gear box to throw in my r32. but the engine doesnt hav a turbo. so i am plannin to get sum thing bigger... gt35r ball bearing. i jst wanna noe what else is needed to run this turbo. i am goin to run this turbo on the standard engine. i noe that i need a mainfold, computer, injectors and waste gate... and wot kinda fuel set up do i need? can i use a bigger fuel pump or hava surggie??

i got a rb25det and gear box to throw in my r32. but the engine doesnt hav a turbo. so i am plannin to get sum thing bigger... gt35r ball bearing. i jst wanna noe what else is needed to run this turbo. i am goin to run this turbo on the standard engine. i noe that i need a mainfold, computer, injectors and waste gate... and wot kinda fuel set up do i need? can i use a bigger fuel pump or hava surggie??

a bigger fuel pump will do the trick, you'll also need a front mount if you havent already got one, a 300ZX air flow meter, twin plate clutch, fuel pressure regulator, new dump pipe...

a single plate clutch will do the trick as you probably wont be going over 300rwkws. But if you are or do then yeh a twin plate maybe in the equation.

You may not need a manifold either as you can use the std one but grab one of AM-PERFORMANCEs external wastegate adapters.

A bigger fuel pump is a must. Grab nismo injectors as they are direct bolt in...no bullshit like with sards.

so is this all i need? so that i can make a tick list of wot to buy

*manifold

*wastegate

*bigger fuel pump

*fuel pressure reg.

*dump pipe

*injectors

*computer

anything else??

$4000 to pay for the above

The quest for horse power is never ending.

All depends how much $ you have

Turbocharger

manifold

custom dump pipe

external wastegate

screamer piping (plumbed back if u want)

aftermarket ecu

Z32 AFM (if you chose an ecu like Power FC that requires one)

larger injectors

larger fuel pump

fuel pressure regulator

front mounted intercooler

custom intercooler piping

pod filter

all that and a good tune will make it work properly....

Edited by _8OO5TED_
  • 2 weeks later...
so is this all i need? so that i can make a tick list of wot to buy

*manifold

*wastegate

*bigger fuel pump

*fuel pressure reg.

*dump pipe

*injectors

*computer

anything else??

Would it not be cheaper to sell yours to a P Plater and buy a Turbo?

Your looking at around $3500 for part and maybe $3000 to fit it up with tune .

And you are unsure if the set up is going to work well

Just my 2c :D

Edited:Sorry, did not see a reply similar earlier.......me bad

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • how do you know voltage is fine?  quick easy test is connect DMM up and put it on max/min mode, remove fuel pump fuse, crank car for 3-5s, go check min voltage You'd be surprised how many "healthy" batteries are showing under 10v during this test in cold weather. 
    • Not properly. You need to be able to dissipate 100 amps or so to doing it meaningfully. You can do it indirectly by watching to see how far the voltage falls during cranking. Unplug the coils or something else to prevent it from starting so you can get a good couple or three chugs. It also helps if you have the multimeter set up reading before you start, and that it has max/min functions. So you can catch the real minimum without having to watch the screen, which often doesn't update fast enough to show the real max/min in dynamic situations. Or use a digital oscilloscope, which can be obtained for <<$100 from Aliexpress (although I'd argue for paying up to ~$200 for a nicer one). A >4 yr old battery will very likely be well down the path to the knackery. Many only last 5-6 years these days. The cold weather lately will definitely make it worse.
    • Hmmm, what do you mean by getting weaker? And where did you get that test done? I've been wondering about my battery because the cold starts crank super slowly. The voltage is fine. Not sure if cranking amps can be checked at home. Battery is 4+ years old.
    • No. The simplest wastegate hookup, with no solenoid or other form of "boost control" (ie, control over your boost control, if you know what I mean) is a single hose, direct from the turbo outlet/hot pipe, straight and only to the wastegate actuator. It is that pressure signal that drives the wastegate to open, providing the boost control (and by "boost control" here, I mean, limiting how high it can go, which is essentially the spring pressure of the actuator). You only end up with tee pieces and alternate flow paths once you start adding things to the boost control system to allow you to determine how much of that boost signal makes it to the actuator. There are so many ways to do that that there is no single way to run the hoses and tees and the like. If you have a stock boost solenoid, then all it does is either allow all the boost signal to go to the actuator, or open up to allow some of it to bleed off. There needs to be a restriction in that bleeder to allow only a small amount to bleed off. And in a stock system, that would then be plumbed back to the turbo inlet (for "emissions control" reasons). That is actually what that nipple on your BOV return pipe could/would be for. If you have an aftermarket boost controller and solenoid, then the above is mostly true, but there is no need for a restrictor in the bleed, because the solenoid is pulse width modulated to create a variable bleed off. The air that escapes from the bleed can either be vented, or also returned to the turbo inlet. For emissions reasons it should be returned to inlet, but the amount of air being vented is so small that it really doesn't matter (either from an emissions perspective, or from an air-fuel ratio affecting perspective).
    • And other times you just need to go buy bigger injectors?
×
×
  • Create New...