Jump to content
SAU Community

Recommended Posts

some one please help!!!!!!!!!!!!!!

ive got no power at all......

no ignition lights.

no head lights.

no interior

central locking not even working. ect ect.

the starter motor isnt even clicking.

it seems like a totally flat battery, but i tried jump starting it and still got nothing. checked the conections. checked all the fuses in the boot, in the cabin, and also in the engine bay but all fuses are ok including the main fuse in the boot.

anyone got any ideas????????

Link to comment
https://www.sau.com.au/forums/topic/14228-my-r33-is-dead/
Share on other sites

The other battery i tried is excellent i use it in my other car no probs. ive checked all the fuses including the main fuse.

Gloof i do have an immobiliser, if this is at fault could this stop power to everything though?

Link to comment
https://www.sau.com.au/forums/topic/14228-my-r33-is-dead/#findComment-286913
Share on other sites

i found the problem..............

i must have left the interior light on, the night before it died which ment the battery was totally dead. then in the morning i had nothing tried to jump start it after checking all the fuses and it wouldn't even jump start so i continued asuming the problem was in the car...........

later with the multimeter in my hands i desided to check the jumper leads i was using for continuity. and to my surprise it turns out they where stuffed for some reason they whern't carrying the current??????? they where brand new antizap leads???????

so i tried a different older pair of jumper leads and it started...

end of drama....

Link to comment
https://www.sau.com.au/forums/topic/14228-my-r33-is-dead/#findComment-288111
Share on other sites

cheap jumper leads are worth their weight in packing foam. :D the el cheapo chinese ones have the cable crimped onto the ends through the insulation and generaly are open circuit. either buy decent leads or cut the clamps off, bare back the jumper cables and solder them onto the clamps.

usually even if they do make contact the actual wire is so small theyb wont pass enough current to start a car without glowing red hot and melting all the insulation off them :P

Link to comment
https://www.sau.com.au/forums/topic/14228-my-r33-is-dead/#findComment-288246
Share on other sites

Al

i know i should have just replaced it (now)

but i thought i had a serious prob. any way my mistake.

secoh

the jumperleads i was using where (looked) like very good quality. they are the anti zap ones 400amp from a good spare parts dealer. must have just been a dud set.

Link to comment
https://www.sau.com.au/forums/topic/14228-my-r33-is-dead/#findComment-291420
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm thinking that this is such a small part of the problem that you could easily forego the vac pump and just achieve 90% of what you need, which is keeping the gate open when off boost. It's not as if there are not already techniques to keep a gate fully closed under boost. After all, you have boost. Just use a wastegate actuator that will allow you to apply the boost on the appropriate side, just like every external gate out there.
    • Heres another fitment photo. redrilled the pattern to 5x112, and threw my audi´s rims on. had to touch the upper control arms with grinder, because the "sharp corner" was sticking about 2-3mm on the tire path. i have the "fender lip" mostly cut off, otherwise these (too) would contact with it. 20x9.5 ET25 rear    265/30 20x8.5 ET20 front    255/30 they are temporary, and look too big for the chassis. searching for 19s to it.
    • From experience, it will come back to bite you haha.
    • Background: my BMW 225i hatchback (rebodied MINI/X1) came with 3x RE003 and 1x Goodyear Asymmetric something. The RE003 roared and slid around, the Goodyear side was quiet and grippy. Definitely my car was thrashed before it got sent to dealers. My brother also got RE003 all round on his old VA WRX STI, I wasn't impressed with them, car was loud so can't comment on noise. Anyway, Hankook stopped making/updating V12 Evo2. So bought S1 Evo3 runflats. Great daily duties tyre and not that harsh ride. Tyre reviews site/youtube rated them as best stopping in the rain and I believe them. Next set, Goodyear Asymmetric 5 non-RFT. It beat PS4 in tests and is like $100 cheaper, so put them on. Great tyre, more grip then S1 Evo3 but a tad noisier as expected, still rocking them. Next set I am looking to go runflats, probably the new Hankook Evo. Although the new Pirelli PZ5 did well in tyrereviews test. Or go Goodyear Asymmetric 6 which was top tyre last year. The V12 Evo2 on my gen5 Liberty GT wagon did great in cold condition (drove to snowy mountains for a day so my husky can feel his ancestor's roots). Super impressive performance for $120 each lol. Never skimp on tyres, brakes, suspension. There's old pics of my R31's crappy random brake pads bending in the caliper at Oran Park track day somewhere around here. Anyway, my 2 cents.
×
×
  • Create New...