Jump to content
SAU Community

Recommended Posts

Thanks heaps guys, if only I had the money.

I was talking to somone in an Import shop (not giving away names) and they told me that the Autech R33 sedan was not able to be complied in Australia because controlled crashes have not been performed on them. Is this true???

Link to comment
https://www.sau.com.au/forums/topic/142674-wtf/page/2/#findComment-2660665
Share on other sites

HPI had a story on a black skyline 4 door that had a gtr conversion - this is probably the same. Still, if someone is keen, they should check it out - if its done properly it might still run well.

I'm pretty sure it was in speed magazine, not hpi though i could be wrong.. Pretty sure its the one out of the mag..

Link to comment
https://www.sau.com.au/forums/topic/142674-wtf/page/2/#findComment-2661245
Share on other sites

Its not real, thats the one Ernest Parry built a few years ago and yes it was in HPI. Its still missing the few touches that make a R33 GTR sedan different - ie series 3 xenon lights, interior etc. A propper Autech R33 4 door goes for much more than what he's asking.

Link to comment
https://www.sau.com.au/forums/topic/142674-wtf/page/2/#findComment-2662778
Share on other sites

there is a ture one up at mooloolabah I have seen it parked there a couple of times but never find the owner :D

is this what u are talking about.....

there is a proper impul version up here yes, had the plates 25.MAT on it, been for sale for ages, but its not a GTR its only a 4 door impul version. with a few tasteful mods.

he has been a member on this site ages ago but havent seen him around for a while.

now doesnt have the plates, only has standard ones on it, i see it most days going to work.

here is a link to it for sale.

http://www.carsales.com.au/pls/carsales/...p;category_id=3

Edited by 85URK
Link to comment
https://www.sau.com.au/forums/topic/142674-wtf/page/2/#findComment-2667983
Share on other sites

Ok he just got back to me. It has been made from an R33 V-spec GTR with Autech parts, flared rear quarters and door. Made by Skyline Imports QLD.

VIN is 6U9000ENR33005578

Booya,h yeah I was 99.9% sure it was his old one, used to see it a fair bit so knew the trim/wheels.

Link to comment
https://www.sau.com.au/forums/topic/142674-wtf/page/2/#findComment-2673321
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...