Jump to content
SAU Community

Rear Bar Swap(how To?)

NYTSKY

By NYTSKY,
in Exterior & Interior Styling

 Share

Recommended Posts

NYTSKY Grand Master

NYTSKY

Posted
Posted

Ive just purchased a 400r rear bar for my R33 series 2.What is the correct way of removing the old bar and fitting the 400r bar???

I can see i have to remove the screws in the wheel arches what else???

CHEERS IN ADVANCE

Link to comment
https://www.sau.com.au/forums/topic/142936-rear-bar-swaphow-to/
Share on other sites
dead32 Mentor

dead32

Posted
Posted

best way i could explain it is to look at your new bumper, see where the bolt holes are in that and then go to your car and look in that area, bolts in the wheel arch plus 2 bolts either side of the bumper in the middle.

candy33 Experienced

candy33

Posted
Posted

to remove the original bar you need to remove the clips underneath the 'skyline garnish'

then inside the boot behind the plastics near the jack are 3x 12mm nuts and the same on the oppsoite side aswell. the screws inside the wheel arch that you mentioned and also the bolt that holds the number plate in.

hope that helps :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...