Jump to content
SAU Community

Recommended Posts

I am selling my HKS 2535. It comes with RB20 Actuator and HKS elbow is included.

As you know these are a very good streetable turbo. Its not a lag monster and gives lots of boost in the midrange just where you want it for the street. Perfect for an upgrade from a stock turbo with no loss of power down low

I ran 12.1@116mph in normal street trim. As you see by the times, it certainly not slow

$1400

Im in Melbourne

Sorry, doesnt come with lines

post-14092-1163666460.jpg

post-14092-1163666487.jpg

post-14092-1163666514.jpg

Edited by Robo's
Link to comment
https://www.sau.com.au/forums/topic/143497-hks-2535-for-sale/
Share on other sites

Why are you selling?

Got any pics and comments on general condition?

As ryan asked....do these bolt straight on? ie, exhaust T3 shouldn't be a prob but does the original dump/down pipe bolt on with no mods?

Will post some pictures up tonight. Im updating turbo's, so far ive gone 2530, 2535 and now a GT3071.

Will bolt straight up to your dump and inlet pipes. You just need to make sure you dont have the little seperator between the wastegate and the turbine on the exhaust side of your dump.

Where did you get your oil/water lines from?

I read some of your posts and i think you managed around the $100 mark...or was that just the start?

Got them from a place in Brooklyn, Vic, Pirtek would have them too. Take the turbo in, its pretty easy to match them up.

Got them from a place in Brooklyn, Vic, Pirtek would have them too. Take the turbo in, its pretty easy to match them up.

hey mate

just giving u a free bump i just purchased one of these not long ago for $1700 so $1500 is a bargain good luck with the sale and the new turbo upgrade :D

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Order for the 2025 model R35 GT-R were accepted from 3rd March and 26th August the last order rolled off the production line at the Tochigi plant. Concerning the R35 GT-R replacement, current Nissan CEO Ivan Espinosa said "Nothing has been decided about the GT-R at this time, but we are well aware that everyone is waiting. The GT-R will evolve and reappear in the future. Please be patient until that day comes." Nissan has a lot of issues with management and finances so take Espinosa's words with a big grain of salt. From what discussions I've had and read about here in Japan, not a lot of people are confident about Nissan's future, let alone the next GT-R. 
    • Thanks. We getting some parts along too so he will be solving the speed issue like next week so i will let you know what he came up with.   
    • 21 is explicitly the coils detected as the issue. Is it guaranteed the actual issue? No. Just the ECU thinks it is. When you say rattling, describe it better, get an audio clip as best you can if possible.
    • Yea got me coppers. Bad news is I just put them in and the car still has the light and shakes. I also noticed I hear like rattling coming from the exhaust piping right under me. Does 21 also have a possibility of being O2 sensors?   So, coil packs are good, the harness is good, the MAF is working, and obviously the spark plugs just replaced and working.
    • Make sure you drop the GTT base tune back in, and set your injectors again, this will remove anything playing up with it you may have removed. Possibly lean there as it's normally a fast transient going THROUGH atmospheric pressure, and a turbo motor would then quickly go richer as boost builds. The only worry you MIGHT have is ignition timing, as the DE is higher compression than the DET from memory. But again, you're not in boost, so the DE motor will be a lot more forgiving at atmospheric.   Get Murray, Kinkstahs, and Johnny's input on tuning haltechs, those guys have played with tuning enough in the past to be able to help now you're past the trouble shooting stage of the MAP issue
×
×
  • Create New...