Jump to content
SAU Community

Recommended Posts

guys i was wondering if its possible if you can post pics of ur cold air intake setups and heat shield setups you have used on ur r32's. reason beaing that my air filkter is just sitting there sucking in a SHIT load of hot air and im unsure of how to defeat this issue.

so any suggestions and fotos would be awesome!! THANKS AGAIN

Link to comment
https://www.sau.com.au/forums/topic/144158-air-filter-shielding-on-an-r32/
Share on other sites

you obviously have a opipe that comes from outside and rams co0ld air in there yer?

send me other pics if u can yer...when u geta chance

well I didnt buy it, a mate of mine made it for me

this is the only pic I can find atm.. just a side shot

Its abit more expensive but i never get any hot air into the turbo this way... :):(

yer, i was thinking of that idea, but the wet weather put me off....so any problems as yet? and does water stuff up the airfilter?

Ive had the filter get abit wet from a rainy day and had no drama's.

The induction noise is much louder, performance i wouldn't think i gained much as at the end of the day the air has to travel through the turbo then intercooler where it actually gets cooled, i did it more for piece of mind that the motor isn't gettin heat soaked when im just sittin there in summer! >_<

looks good, but do u hav induction piping from underneith into that box or not?
the box is only on the sides, so there is already air comming in at the front

factory cold air feed runs under the headlight, just uses that

performance i wouldn't think i gained much as at the end of the day the air has to travel through the turbo then intercooler where it actually gets cooled, i did it more for piece of mind that the motor isn't getting heat soaked when im just sittin there in summer! >_<

A CAI is always much better than a pod sitting in air heated by the radiator. There are real losses, especially as the weather warms up. I notice almost no difference on a hot day. Feels the same. Unsure if those with pods feel a difference as I've never ran one.

----------------

I've always ran the stock airbox, I've plumbed 2 x 45degree 100mm pvc pipe in to the stock airbox. Looks all neat and tidy.

Probably could attach the stock cai to it to hide it a little more.

When I first did the cai I checked the filter to see how wet it was after a long wet drive. It was almost dry, the afm was definitely dry as was all the piping and top side of the filter. The bottom of the box was still dry also. Just the filter felt ever so slightly slippery on the bottom side.

I did punch it through puddles and had ppls driving in front spraying up plenty of water.

post-382-1164185835.jpg

I disagree, i get no heat when i stick my hand in that area what so ever (tiny bit if you thrash the hell outta it off the IC pipe), the radiator heat runs behind that, it is where the factory cooler would sit and even has the cuts in the wheel arch behind it to keep airflowing through >_<

I have had no problems with water, and to be honest i find the temp of the day doesn't really change how the car drives like it used to sitting up near the motor. I used to get abit more lag or abit less power down low, now its much smoother n almost always the same. Induction noise is much much louder and it looks sh*t hot when you open the engine bay.

I may even chuck it on the dyno and see if it makes any more power for a test! I wouldn't guess it would make much more, but maybe 5-10 rwhp max. It was more about the motor gettin heatsoaked in summer as i notice its startin to get hot and this has really helped. You will ALWAYS have ambient air blowin onto it even at 5kms an hour as its in a direct flow area rather than sittin around in an engine bay.

Personally i think either will do the job just aslong as the pod has a good source of air flow and is blocked from heat, that thing under the headlight isn't really any good

hmm........std box? but there is no sucking noise ey? BORING!!! lol...the filter down behind the bar seems cool....but yer...wat if the dampness gets in the afm? is that bad?

It doesn't... I've had it like this for almost 5years and ~150,000km's. >_<

Its actually quite loud, in the cabin its not with the windows up but passenger window down it is loud, however its very much louder on the side of the road, on par with a pod and you can hear the loud sucking noise from the bumper area rather than just everywhere.

I may even chuck it on the dyno and see if it makes any more power for a test! I wouldn't guess it would make much more, but maybe 5-10 rwhp max. It was more about the motor gettin heatsoaked in summer as i notice its startin to get hot and this has really helped. You will ALWAYS have ambient air blowin onto it even at 5kms an hour as its in a direct flow area rather than sittin around in an engine bay.

Chances are you won't see an increase in power as when you run up on the dyno the operator places the IT sensor where the air is sucked from, if its a pod usually on the pod, if its the stock air box inside the CAI.

As the POD see's a higher inlet temp from air passing through the radiator the IT sensor see's this, reports it to the dyno and the dyno pumps up the power figure to supposively 'compensate' for the given car's poor setup. Thats the way I look at it anyway >_<

Shove the IT sensor in the cai of a box and the it sensor reading will be lower so no or very little power correction will be made.

I've always strongly believed shoot out mode is a load of crap for this very reason, it should be placed in front of the car in the stream of the air leaving the big arsed fan. If you run a pod the motors going to suck hot air thats passed through the rad, so its going to make less power, if it runs a good cai and box its going to make more with no adjustment to the power reading other than the temp of the air the car is being blasted with. Reflects more so the real world on road performance with the bonnet down.

If that makes sense.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...