Jump to content
SAU Community

Recommended Posts

Hey guys,i test drove a 1995 r33 GTS-t today and i got to admit it was fun but the only thing i didn't like was when you would take off in first (i didnt try takeing off in any other gears). the engine (not to sure if it cam from the engine it sounded like it came from the left hand side of the car) would make a rattling noise it was really bad, would any body be able to help.

Best regards Vlad Adam

Link to comment
https://www.sau.com.au/forums/topic/144471-r33-problems-rattle/
Share on other sites

would it only do it with the clutch either in or out. it may be that the clutch is noisey (either the springs on the clutch plate or one of the bearings).

When i start to de-press the clutch, and take off it woiuld start to do it and then continue till i would change to second or boost would kick in, but it would not do it when the car was heated up.

If it's under any kind of load a 'rattle' like marbles in a tin is our good chinese friend 'ping'. If it's a sound coming from the 'left side of the car thats consistant with Mr Ping.

Mr Ping is visiting with his good friend 'Too much base timing'.

Make a mark on your CAS to see where you started with a marker pen, losen the bolts so you can rotate it. Get out your trusty Timing light take a few degrees of base timing out at idle, tighten it back up and see if it fixes the noise. In the mean time DONT try to make that sound anymore. If it means not driving you car till you can do this then so be it. RB25's 9:1 compression doesn't make for forgiving ringlands under boost with ping.

See how you go. It's not uncommon as an issue.

If it's under any kind of load a 'rattle' like marbles in a tin is our good chinese friend 'ping'. If it's a sound coming from the 'left side of the car thats consistant with Mr Ping.

Mr Ping is visiting with his good friend 'Too much base timing'.

Make a mark on your CAS to see where you started with a marker pen, losen the bolts so you can rotate it. Get out your trusty Timing light take a few degrees of base timing out at idle, tighten it back up and see if it fixes the noise. In the mean time DONT try to make that sound anymore. If it means not driving you car till you can do this then so be it. RB25's 9:1 compression doesn't make for forgiving ringlands under boost with ping.

See how you go. It's not uncommon as an issue.

from what i could see when i was taking a look at the car it's pritty much standerd, exept a blow-off -valve, a fool 3 and 1/2 inch exhaust system. and boost controler (valve type). some1 did mention that it was the intercooler pipings and now that i think of it the guy had aftermaket pipings, but a stanerd intercooler. so would that be it!!

And it was like a vibration with a lill bit of a rattle! (im sorry i cant really put a finger on it my haring is not that good so i had to get a trust worthy friend to come with me when i did then test drive, i could hear it but not that clear, im just going off what he explanied it like)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...