Jump to content
SAU Community

Recommended Posts

Hey there,

I've just noticed this today, as I don't really boost my car often but after I took it for a run to make sure it was running well after I was working on the motor I noticed that the car is only boosting to about 2-3PSI?

It had a boost control on it, which was turned right down because I just had a forged rebuild so I took off the boost control and connected it normally, still seems like it's only boosting at 2-3PSI on the stock boost guage as well as a aftermarket boost guage.

Any ideas? All hoses etc seem to be connected well checked everything I could...

Link to comment
https://www.sau.com.au/forums/topic/144683-boost-problem/
Share on other sites

  • 2 weeks later...
when you say 2-3,do you mean 2-3 on the stock gauge?

because that is normal...

Yeah, I do mean on the stock guage. My other guage ain't that great so I can't go off that either.

I'll go over the car this weekend T04GTR make sure all that is alright.

But, Waz - so it's normal only to go to 2-3PSI on the stock guage then? So, It's just me? :(

Link to comment
https://www.sau.com.au/forums/topic/144683-boost-problem/#findComment-2728776
Share on other sites

Stock boost under 4500rpm is 5psi and 7psi over that.

So 7 on the guage is 7000mmHg or whatever the multiple is, which is about 1 bar I think? So you should see about halfway between 0 and 7 when on full boost.

Link to comment
https://www.sau.com.au/forums/topic/144683-boost-problem/#findComment-2728893
Share on other sites

stock gauge is in mmHg (that millimetres of mercury)

and the conversions are: 760mmHg = 1bar = 1atmosphere = 14.3(ish) psi

and the stock gauge is read at x100mmHg

so...

+7 on the stock gauge actually means 700mmHg which is a tad under 14psi

and so on a stock R33, which runs 5psi then 7psi higher in the rev range, you would expect the stock gauge to read between +2 and +4 on the stock gauge

that is 100% normal :D

from my experience, the stock gague is pretty accurate. its flaws are that is it hard to read because of its units aren't commonly talked about, its in a hard position to see, and that it can't read over 14psi

Link to comment
https://www.sau.com.au/forums/topic/144683-boost-problem/#findComment-2731327
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If they can dyno them, get them dyno'd, make sure they're not leaking, and if they look okay on the dyno and are performing relatively well, put them in the car.   If they're leaking oil etc, and you feel so inclined, open them up yourself and see what you can do to fix it. The main thing you're trying to do is replace the parts that perish, like seals. You're not attempting to change the valving. You might even be able to find somewhere that has the Tein parts/rebuild kit if you dig hard.
    • Can you also make sure the invoices on the box (And none exist in the boxes) are below our import duty limits... I jest, there's nothing I need to actually purchase and order in. (Unless you can find me a rear diff carrier, brand new, for stupidly cheap, that is for a Toyota Landcruiser, HZJ105R GXL, 2000 year model...)  
    • Murphy strikes again! Nothing at all would have gone wrong if you had the tool kit in the car! You'd have just found the clamp loose the next time you went to touch it...
    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
×
×
  • Create New...