Jump to content
SAU Community

Recommended Posts

I have 2 sets of these for sale and I will not split them up. SCHROTH (http://www.schroth.com/) Safety Products are used by Holden Racing Team, Larry Perkins, Russell Ingall, Ford Tickford Racing. Sparco harnesses are made by SCROTH. So too the ones in the Renault F1 cars :P

- One Rallye Cross ASM, one Rallye 4 ASM.

- Full instructions, eyelet bolts included + boxes too :)

- Both bought at the same time (2 years ago) from www.gmpracingproducts.com.au

- One of them is a unique design which allows you to quick release the harness easily to allow passengers to get into the rear seat quickly without having to undo the harness.

- 2inch.

Some pics:

1.jpg

Wrong pic (this one shown is a bolt in harness). I have the quick release version which uses eyelets so you can completely remove the harness easily at any time.

strip_01.jpg

In the car.

Specs:

4-Point Static harness belt.

The individual shoulder straps eliminate the separation buckle allowing either wrap mount installation to a harnessbar or bold mount to rear seat lap belt anchorages.

Shoulder and lap belts: 50mm (2") wide webbing.

Single push-button buckle for connection and release.

Clean condition, comes with full eyelets set. Not damaged at all in any way or form. In Sydney eastern suburbs. Can send them if I have to via. courier. You pay shipping though ($20). Asking $150 for the pair.

Link to comment
https://www.sau.com.au/forums/topic/145113-fs-syd-2-x-schroth-racing-harness/
Share on other sites

Back up for sale. Sale dropped through because buyer changed his mind and wants to go 3inch.

To answer some PMs: No expiry date is set on these. I have no idea if they are FIA approved or not but I assume so as Garry Motorsports who sold them to me are race specialists.

Also. I have packed them all up and realised one eyelet bolt is missing. I called Revolution Racegear, they have heaps in stock for $10 each.

So price reduced to $140!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...