Jump to content
SAU Community

Where Is The Diagnostic Port On Rb20det Engine Loom?

s13rb20det

By s13rb20det,
in Engines & Forced Induction

 Share

Recommended Posts

s13rb20det Enthusiast

s13rb20det

Posted
Posted

Hi Guys

Took my car to unigroup engineering last night to get a dyno tune and fix up some running rough at cold start issues. He was looking for the diagnostic port to plug into so he could find out what was happening under the hood althoug he couldnt find it. I have been searching for the RB20DET wiring diagram although i cant seem to find it. Could anyone please direct me to where this plug/port would be located or a wiring diagram so i can attempt to find it myself. Help is much appreciated thank you.

BHDave Grand Master

BHDave

Posted
Posted

If it was formerly a CA powered s13 they don't have a consult port.

You will have to wire one in direct off the ecu. It's not hard, i've done a couple myself. If you find an rb20 wiring diagram the consult plug wiring is normally shown in the top corner somewhere. There are 4 signal wires plus a power and an earth from memory.

s13rb20det Enthusiast

s13rb20det

Posted
  • Author
Posted
If it was formerly a CA powered s13 they don't have a consult port.

You will have to wire one in direct off the ecu. It's not hard, i've done a couple myself. If you find an rb20 wiring diagram the consult plug wiring is normally shown in the top corner somewhere. There are 4 signal wires plus a power and an earth from memory.

You've been a massive help thank you very much :D , yes it was formerly a non turbo CA... Would you have any idea where i could find an rb20 wiring diagram?

NewKleer Mentor

NewKleer

Posted
Posted (edited)
You've been a massive help thank you very much :glare: , yes it was formerly a non turbo CA... Would you have any idea where i could find an rb20 wiring diagram?

http://www.ecutalk.com/images/consult_car.jpg

http://www.ne.jp/asahi/tomosang/skyline/mainte/wire.htm

the wiring link, even though in japanese, shows the (RX), (TX) etc in brackets for consult port. theres probably better ones around. IGN and GND dont have to be connected to ECU, just any IGN switched power supply (ecu is easiest)

ive got a car side consult plug if you need one ($16 posted)

Edited by NewKleer

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      R32 GTR Limp Mode?

      By joshuaho96 · Posted

      Join the NorCal facebook group btw, but if you can confirm it is HICAS I would install a lock bar and do the work to keep the HICAS control unit happy despite the hardware not functioning. The HICAS control unit is also responsible for speed sensitive power steering so if it's unhappy you'll get failsafe/heavy power steering. A standalone can control that power steering solenoid valve but sometimes it's just easier to stick with the factory setup. Tomei makes a little electronic module that you can install to fool the control unit. I would probably go through the effort to not use a scotch-lok and build a harness so I don't have to chop up the OEM harness. Where you could source those connectors and pins I wouldn't know at the moment though.
    • GTSBoy
      Pops when backing off throttle, rough-ish sound through rev range.

      By GTSBoy · Posted

      Oh, another question comes to mind though. What sort of shitty fuel are you feeding it. Mine, a turbo, has to be fed 98RON, so it doesn't ping itself to death. 98 in Oz is good, dense fuel with minimal oxygenated compounds. Meaning that the energy density is high, and if the O2 trim is working, you will get more MPG than with a lesser fuel. If you're using some sort of piss poor E10 blend with some other MBTE or other oxygenated additions, that could explain using more per mile.
    • Nydt
      R32 GTR Limp Mode?

      By Nydt · Posted

      I have no idea where the thump is coming from, it sounds like its from behind me but im not exactly sure. And it was the HICAS light that came on.   I think a complete delete is the route im going to go. Probably going to pick up the kit within the next month and get it installed. HICAS is just going to end up being a headache if I keep it.    Thanks you. 
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Just putting this here for reference for other beginners. Similar to what I said above.  I learnt if you have a few dents that are fairly close to each other (within a couple of inches maybe 2-4 inches?) Use filler across them all and sand it all at once with the long block as opposed to fixing them seperately.  Will make life MUCH easier because you won't get stuck in the cycle that I did. I think doing it seperately there is some overlap (mean your whole repair zone might cover near the area of the other dent) and you start sanding near the other dent making a low spot.
    • GTSBoy
      Pops when backing off throttle, rough-ish sound through rev range.

      By GTSBoy · Posted

      Hence why I suggested some tests.
×
×
  • Create New...