Jump to content
SAU Community

Stock R33 Turbo, Rear Hausing Need One Asap

WogsRus

By WogsRus,
in Tasmania

 Share

Recommended Posts

WogsRus Veteran

WogsRus

Posted
Posted (edited)

There is a lot of ORs there. But basically my car is experiancing boost creep, as the stock wastgate is too small with all the mods. So i need to have a look at a stock hausing to see how much i can machine out.

Can comone post a pic up of the gate, closed and opened, so i can get an idea how much you can take off.

Alternativaly. if somone has a stock rear hausing, can i buy it or lease it, so that i can machine the hausing and then swap mine over etc.

Also, if anyone has an R32 10psi actuator, can you give me a bell.

As is the car boosts to 10.6psi with the gate fully wired open. The problem is the wastgat starts to open at 7psi and the GIZZMO IBC can not compensate for that much creep.

ALSO how else can i cure boost creep? At the moment, the wastgate pressure tap is taken form the IC pipe, before the TB, like the stock one, if i tap it off the turbo hausing, will that help at all.

Edited by WogsRus
skidkid Proficient

skidkid

Posted
Posted

G'day, I have an R32 turbo I split in half and ported the w/gate hole but needs bigger flap made and fitted. I have a piece of stainless to turn one up. Without replacing flat you would be lucky to port 2-3 in diameter out of w/gate outlet hole (going by R32 turbo).

WogsRus Veteran

WogsRus

Posted
  • Author
Posted

so how much can i port keeping the standard flap, 2-3mm or something like that??? I only need to reduce the creep by 3 psi, but if you can only take out so little, i might just leave it and run with 10.6 psi LOW setting.

toffy Veteran

toffy

Posted
Posted (edited)

i have an r34 turbo lying around somewhere absent the exh wheel, ill dig it out for you as i only wanted the compressor housing :miner:

edit: just putting the r34 housing on "might" cure your problem because i would expect that nissan would have corrected that with the neo turbo?. just a thought

Edited by toffy
toffy Veteran

toffy

Posted
Posted
HAY toffy, you got that R34 housing somwhere???

yeah mate, ill dig it out for you, its upto you if you wanna buy it or not, i say try it on and if it doesnt fix the problem then port yours and give mine back?, hows that sound? >_<

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...