Jump to content
SAU Community

Recommended Posts

Many many thanks :)
I'll fill up this space today when I can about the VS2Nur and the N1 both featured together in...
a) Performance Garage #11 last month and
b) Performance Imports #161 also last month.

Matt and I dedicate these pics to...

Adrian Hodgson, Editor of Performance garage

Jason Round, Editor of Performance Imports and

Eric Tang Photographer

ETang-0296_zpsb6d26e7f.jpg

ETang-0000A_zps46ac403f.jpg

ETang-0151_zpsdc8d07d3.jpg

ETang-0000B_zps5ed22a8b.jpg

And perhaps I'll dedicate this post to Nick Nikolas and Terry Ashwood as they both share the story of the Black V-Spec II Nur coming to Aust and its later development.

Story as reported after Matt and I have had discussions with Terry Ashwood and Nick Nikolas:-

* The 2002 Nur was brought out to Australia in 2002. In other words, it was a new car. It was purchased by Terry Ashwood at a new price.

* The Nur still had plastic on the seats and door cards

* The odometer had about 200Kms on it

* Terry Ashwood's intent was to keep it pristine with ultra-low Kms.

* It could have feasibly been sent back to the Omori factory in Japan to become a Z-Tune

* That's the direction Terry wanted to take until he sold it to Nick Nikolas - and we respect that!

* At the time of sale, Terry had put on 19"x10.5" Nismo LMGT4 wheels and a Apex'i Power FC D-Jetro ECU

ETang-0051_zpsc8bca76f.jpg

ETang-0178_zpscbed5d80.jpg

ETang-0176_zps0d3fcbf7.jpg

ETang-0171_zpsa9c07252.jpg

* Nick Nikolas took this Nur in a different direction - Matt and I respect that decision as well; otherwise Matt wouldn't have bought the car

* Nick used to own the JUN R32 GT-R which was doing 9s on street rubber at Cootamundra. That GT-R was an ADM. Nick has a few regrets about doing that to an ADM lol

* Nick did a few things (as you can see below) to the Nur that helped it do a 10.9sec run at Cootamundra. He only wanted to do that once and then preserve the car at low boost.

* Nick replaced the silver 19" LMGT4s with 20" Volk GTCs

* The Nur had a Big Brembo Brake Kit with floating discs and braided lines installed at over $20K

* Top end Ohlins Coilovers installed

* Ikeya Chassis Dampers front and rear

* C/F Prop Shaft from the UK

* The Nur also had Jun cams/gears, Nitto Oil pump, Large injectors, Nismo Fuel Reg, Larger Fuel pump (with an extra Nismo one spare), ARC Intake with Nismo piping installed

* Top end Motec ECU replaced the D-Jetro

* Nismo plenum was installed

* Nismo Titanium twin pipe exhaust

* Nismo MFD and Cluster installed

* The side skirts, rear pods are genuine Nismo

* The C/F VS2 bonnet was kept as a spare and replaced with a genuine Z-Tune with R-Tune intake kept as a spare

ETang-0124_zps8b12f1c4.jpg

ETang-0122_zps962c533b.jpg

ETang-0126_zps9f69ee57.jpg

Piping is all there; but it's been turned off for ages.

ETang-0070_zps627e8ef4.jpg

ETang-0074_zps4a3b4c8a.jpg

* Matt has an ultimate street and track car which may make the track again one day soon so it can at least be tested around corners!

* Matt is the third owner, and yet this NSW car only made its first appearance at Legends Night in 2009, parked next to Rod Markland's GIO Chassis #4 GT-R

JoelyMoley-16.jpg

Terry-2_zps99667a40.jpg

Matthew-2_zps6f77ff4f.jpg

Matthew-4_zps270d86ce.jpg

So three owners of this Nur there have been...

Three nicer guys you'd go a long way to meet :)

* Terry Ashwood

* Nick Nikolas

* Matt Tung-Yep

And perhaps I'll dedicate this post to Kristian Appelt and Todd O'Donnell as they both share the story of the V-Spec N1 coming to Aust and accidentally landing in my hands.

Story:- Many people may know that I've had a connection with Kristian and Todd for quite some time.

After all,...

Terry-12_zps8d485b6f.jpg

Todd brought in my Bayside Blue V-Spec II with full Japanese history and barely 40,000Kms on odo. Both Kristian and Todd eyed off this one.

Terry-49.jpg

Todd instead, waited and waited for an N1. But so too was his mechanic back in Nara; and thus, it was going to be an arm-wrestle between friends at auction if no-one else bought it first.

Enter Kristian... He sits over auction houses in several countries and pores over specs all day long. And then he saw this...

Terry-2.jpg

Hey! And it didn't seem to be designated as an N1 either!

Kristian already had a V-Spec II N1, so knowing that Todd was looking for either a V-Spec N1 or a V-Spec II N1, contacted him.

And Todd said "YES!"

Terry-41.jpg

But Todd was stuck with a yard full of Corvette, Harley F400, Supra, 360, etc... that needed to be MOVED!!!

Time ran out for Todd and I had 36 hours to decide - and I'd only just completed a build on the VS2 under the advice of Steve-0, Piggaz and Yavuz at Unigroup Eng.

ETang-0232_zpse7f704ef.jpg

So here she is in my name - thanks to Kristian firstly (aka Iron Chef), and then Todd (aka JLM).

ETang-0283_zps0223f795.jpg

Not much different looking under bonnet to see if you removed all the Nismo items...

But just like the Nur above, it has "24U" stamped on the block on the passenger's side = N1 engine.

ETang-0164_zps9d84122e.jpg

Still pretty though...

and it shifts - after you get past the lag, lol

ETang-0161_zpsb3d1fc55.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...