Jump to content
SAU Community

Dyno First Run

Light

By Light,
in Engines & Forced Induction

 Share

Recommended Posts

l0WRB Mentor

l0WRB

Posted
Posted
Just pump boost into it until you either get valve float, no gain, or run out of fuel.

I think the limiting factor in your setup is the walbro intank pump. You may find that your injectors are maxing out earlier than expected if it isn't up to the task.

Stock valve springs and lifters will likely stop the fun at about 20psi anyway.

i know of a few cars making around 300rwkw GENUINE rwkw not this shootout mode stuff...and they are running walbro intank pumps so this pump should be fine for ur application

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

"Genuine" you reckon?

My walbro (6 months old) ran out @ 250rwkw/15psi with my GT30

Installed a Bosch and instantly the AFR's dipped into the 10's from close to the 14's...

And that wasnt making any other changes.

And im not the only one to have issues.

So theres a personal expirience for ya :P

Devils_Advocate21 Mentor

Devils_Advocate21

Posted
Posted

How do you know if its a GENUINE walbro pump it could be a copy :O good apples vs bad apples unfortunatley the bads are winning on the walbro pumps. If thats any indication of quality plus rectification of this now saves hassels later on id say

l0WRB Mentor

l0WRB

Posted
Posted
"Genuine" you reckon?

My walbro (6 months old) ran out @ 250rwkw/15psi with my GT30

Installed a Bosch and instantly the AFR's dipped into the 10's from close to the 14's...

And that wasnt making any other changes.

And im not the only one to have issues.

So theres a personal expirience for ya :O

maybe u had a dodgy pump or a crap tuner? my mate has 292rwkw @ 18psi on his rb25 with a walbro intank pump has runs fine and even runs a bit on the rich side just to be safe and thats on a dyno software thats so old it would prob read well over 330rwkw in shootout mode.

Light Enthusiast

Light

Posted
  • Author
Posted

hey mates how are you doing?

I took my r32 to the dyno last thursday, anyway it was not a (tuning) as the man of this dyno-the only dyno in my region- does not tune power fc's, it was more of power measurment day.. any way I will post the dyno graphs and you will see that i have issues on AFR plus very thick blue smoke..i took it to my tuner after the dyno and he modified on the AFR thru the commander (all he can do) using wide band (innovation), the innovation shoed better AFR on the street but the thick blue smoke is still toooooo much.

see the graphs and give me your comments please, note that the 347hp graph is on 16.6 psi of boost, and the other one is on 13 psi

Ayman1.jpg

Ayman2.jpg

BHDave Grand Master

BHDave

Posted
Posted

The bump in power doesn't look too good. Boost spike at that point?

Blue smoke not black? Not good, thats due to oil, not fuel.

You're still a bit lean at the top end but could remove a bit between 4500 and 6500.

Where are you located? It would be worthwhile finding someone with a dyno who can tune a pfc, even if you have to travel, but I'd get a second opinion on the smoke first.

Light Enthusiast

Light

Posted
  • Author
Posted

hey BHDave,

thanks mate, I am in Saudi Arabia and tuning is not very popular and thats why i cants find a good tuner easily, even a bad tuner is hard to find :(

we have one good tuner but he only has the software for RB26, I will go to the garage next wednesday and let them check this blue smke, i dont know but it could be piston rings or turbo seals right?

fuel pressure on the dyno (read from my fuel pressire guage) was at 40 on idle and at 60 on high boost, it fell down just a littel to 55 maybe on high boost..

BHDave Grand Master

BHDave

Posted
Posted

You can still get a fairly good tune out of the hand set. If the guy knows rb's then (other than bitching about having to tool around with the hand set) he shouldn't have a problem.

My first tune was done on the hand set as my tuners software didn't like my power fc. It was fine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • GTSBoy
      Best place to order Authetic R32 Parts in Japan

      By GTSBoy · Posted

      I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
×
×
  • Create New...