Jump to content
SAU Community

Recommended Posts

cougarace.jpg

Mazda scrapping all vehicles aboard capsized Cougar Ace

Mazda just announced that it has decided to scrap all 4,703 vehicles that were aboard the Cougar Ace cargo vessel when it nearly capsized off the Aleutian Islands in Alaska back in late July. The shipping vessel sat listing to one side for over a month before it was towed to and repaired at a port in Oregon. During that time, the vehicles on board, comprised of the Mazda3 small car and CX-7 crossover, were tied down at severe angles. Mazda had previously told us it would inspect all the vehicles and sell most as used with full disclosure, considering that many showed little or no signs of damage. Regardless, Mazda reconsidered and the announcement that the entire shipment would be scrapped came today from Jim O'Sullivan, Mazda North America's President and CEO.

The decision not to sell any of the vehicles that were aboard the Cougar Ace must have been difficult to make, considering that we estimate the hull of the ship contained over $103 million worth of vehicles (60 percent of the vehicles on board were the more expensive CX-7, so we assumed a conservate per unit average MSRP of $22,000). Not that we're criticizing Mazda for scrapping the entire shipment, but the destruction of 4,703 vehicles, at least some if not most of which are salveagable, seems like a waste. We're sure there are plenty of non-profit organizations and charities that would be grateful to take these vehicles off of Mazda's hands

PRESS RELEASE:

All Mazda Vehicles From Car-Carrying Vessel

Cougar Ace to be Scrapped

IRVINE, Calif.--Mazda Motor Corporation today announced that all of the U.S.- and Canada-bound Mazda vehicles from the car-carrying vessel, Cougar Ace, which nearly capsized off the Aleutian Islands in late July, would be scrapped.

"After thorough testing by engineers from our American and Japanese R&D centers, we decided the most appropriate course of action – with our customers foremost in mind – was not to sell any of the 4,703 Mazdas aboard the ship," said Jim O'Sullivan, President and CEO of Mazda North American Operations, based in Irvine, Calif.

The Cougar Ace sat listing at more than 60-degrees for nearly a month after an incident at sea, before it could be towed to the Port of Portland, Ore., for repairs and to have its cargo off-loaded.

O'Sullivan added that although some of the Mazdas aboard the Cougar Ace showed little or no visible damage from being tied-down at severe angles for an extended period, the company reconsidered its initial decision to sell any of the vehicles as used.

"We always put the customer first," O'Sullivan continued. "This drove our decision to scrap every one of the Mazdas involved in this incident. None will be sold as used cars."

Headquartered in Irvine, Calif., Mazda North American Operations oversees the sales, marketing, parts and customer service support of Mazda vehicles in the United States, Canada and Mexico through nearly 900 dealers. Operations in Canada are managed by Mazda Canada, Inc., located in Ontario, Canada, and in Mexico by Mazda Motor de Mexico in Mexico City.

Link to comment
https://www.sau.com.au/forums/topic/147571-such-a-waste/
Share on other sites

they should have evened the cars out and not put all the cars to the left side of the ship.....

edit: though its a huge waste, all that metal can be recycled - i hope

Edited by emsta2003
Link to comment
https://www.sau.com.au/forums/topic/147571-such-a-waste/#findComment-2754269
Share on other sites

That was similar to the one in the English Channel about 4 years ago full of BMW's, Audi's and Merc's going from Germany to the UK. Had about 20mil pounds worth on board but that actually sank and water is one of the things that sadly doesnt leave much of the car useable. :)

Link to comment
https://www.sau.com.au/forums/topic/147571-such-a-waste/#findComment-2754277
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...