Jump to content
SAU Community

Recommended Posts

hey guys,

After doing a few hoops i looked down to see that my speedo had died, so i contiuned to check if the cable was broken, the thing is i dont know because the inside of the cable is spinning but the little plastic thing was not attched to the cable, it was in the back of the speedo?

Does this mean its broken as im sure the little plastic needle comes attched with the cable.

any experiences?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/148394-speedo-dead/
Share on other sites

Yep very common. Plastic bit breaks off..

I beleive some places can fix them, after buying several new ones over the years I found out that it was possible :)

They are easy to remove, check around. A place that makes brake lines and cables here in NZ fixes them so try a similar place there.

GTS-T cables are normally not too expensive to buy, but there is no guarantee that it won't break again if it's second hand.

Edited by GTR-Ben
Link to comment
https://www.sau.com.au/forums/topic/148394-speedo-dead/#findComment-2770168
Share on other sites

So my understanding is the the little plastic bit is suppose to be inside the speedo cable it self not in the back of the dash? is that correct?

Sigsputnik: if your speedo works i highly doubt the plastic thing has fallen as it is the mechanism that drives the speedo.

Edited by RaZ_TuRbO
Link to comment
https://www.sau.com.au/forums/topic/148394-speedo-dead/#findComment-2770897
Share on other sites

hang on, what does this plastic needle look like? when i remove my dash, all i see on the speedo cable is, well, the square end of the speedo cable...has my plastic needle fallen off?

(the reason i as is that my speedo makes a clicking noise as i drive)

sigsputnik, thats the sound of a dodgy cable. it hasnt broken yet but possibily will soon. for a 32gtr they are only 100 new from nissan. fairly cheap for a gtr part :)

Link to comment
https://www.sau.com.au/forums/topic/148394-speedo-dead/#findComment-2770918
Share on other sites

u need to remove the cable from the box, where it comes through the firewall is a couple of bolts on a plate, then u have to remove your speedo cluster and it pops out.

A place here in Adelaide actually can put a new steel end on the cable which should never break.

Link to comment
https://www.sau.com.au/forums/topic/148394-speedo-dead/#findComment-2771253
Share on other sites

are you talking about the gearbox end or the speedo end?

u need to remove the cable from the box, where it comes through the firewall is a couple of bolts on a plate, then u have to remove your speedo cluster and it pops out.

A place here in Adelaide actually can put a new steel end on the cable which should never break.

Link to comment
https://www.sau.com.au/forums/topic/148394-speedo-dead/#findComment-2771276
Share on other sites

They are talking about the Speedo end. There is a plastic part with a square end that turns the speedo. This has a spring etc and is attached to the cable. Replacing it with a metal end would be a good idea.. should be stronger from factory.

Maybe this will wear your plastic speedo though, who knows..

Link to comment
https://www.sau.com.au/forums/topic/148394-speedo-dead/#findComment-2771322
Share on other sites

ah, good - so follow the cable from the speedo down? hmmm looks like i'll be in the cabin with a torch tomorrow :P

hope ur got plenty of time and patience. ull hafta remove the dash. the cable goes into the side of the gbox. good luck

Link to comment
https://www.sau.com.au/forums/topic/148394-speedo-dead/#findComment-2772973
Share on other sites

  • 2 weeks later...

guys i got the same prob. and its the second time.....first time it was the plastic piece that had split so it would lock on....i glued it together...put back it and it worked...now its F@#Kd again. So im assuming it the plastic piece again....

should i just buy this piece from nissan? wats it worth?

cheers boys

Link to comment
https://www.sau.com.au/forums/topic/148394-speedo-dead/#findComment-2790979
Share on other sites

just went and bought a new speedo cable for 32 gtst. is it hard to replace? do i need to remove more than just the cluster to get it out? coz i looked down with a torch. i cant seem to see that plate. also where does it come out? down behind the clutch pedal? coz i saw a cable go out there sumwhere.

Link to comment
https://www.sau.com.au/forums/topic/148394-speedo-dead/#findComment-2792583
Share on other sites

also where does it come out? down behind the clutch pedal? coz i saw a cable go out there sumwhere.

I am pretty sure it attaches to the gearbox, but I have no idea how or where, sorry - this is something i need to find out also. the manual doesn't seem to say, which is odd. how much did the cable cost?

Link to comment
https://www.sau.com.au/forums/topic/148394-speedo-dead/#findComment-2793663
Share on other sites

  • 4 weeks later...
u need to remove the cable from the box, where it comes through the firewall is a couple of bolts on a plate, then u have to remove your speedo cluster and it pops out.

A place here in Adelaide actually can put a new steel end on the cable which should never break.

where in adelaide did you get this steel end??

Link to comment
https://www.sau.com.au/forums/topic/148394-speedo-dead/#findComment-2856489
Share on other sites

mine breaks every time I go drifting,The rapid speed changes just breaks the glue loose.

I pull the speedo cluster out, put some araldite in the plastic thing where the spring lives, then some araldite on the square peg that goes into the speedo. Put the plastic thing into the housing, push it in so it's tight with a small screwdriver, then slide the speedo cluster back on.

Some people have had success with using heat shrink to close up the plastic....I didn;t have success. This way works, just has to get done every time I leave the track! haha

Takes me about 30 minutes to do now. I'll take photos next time if I remember,

Link to comment
https://www.sau.com.au/forums/topic/148394-speedo-dead/#findComment-2861176
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...