Jump to content
SAU Community

SA Wasteland?

MM2death

By MM2death,
in South Australia

 Share

Recommended Posts

Sambo33 Grand Master

Sambo33

Posted
Posted

the best thing about exams are when they're finished:D

must be helpful to know how to adjust the pfc, im looking at getting one once my engine woes are outta the way.

would have you subframe movement have been caused by the amount of power transferring to the rear wheels, putting stress on the bushes? are they original bushes at the moment?

  • Replies 6k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Sambo33 Grand Master

Sambo33

Posted
Posted
All my examsn are over. yay!!

hey sam, i was going to call you today and meet up but my bro had my phone and took it out with him. DOH!!

what did boostworx have to say bout the engine?

yo duc! thats alright, my old man came along with me and he had to go straight home afterwards.

yeah Shaun did a couple of quick tests on the engine. its definately rings, could be more than that, but don't know till they pull it to bits. ill get it booked in for the rebuild within a couple of weeks

Nozila Grand Master

Nozila

Posted
Posted

its heavy but i like it as its more of a cruiser than the line or any of the others cars we have. initial pick up power is slow but once it gets going its good - nice torque. I dont know how to drive auto's though, i just put the thing in drive. Anyone know how to launch an auto?

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...