Jump to content
SAU Community

Recommended Posts

  • Replies 6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

this weekend im not doing anything, just 2 pro evo nights, 1 tonight and a bigger one tomorrow night.

Next weekend I'll be having a big mother f**ker, ill give you my number and well catch up then.

No I dont think its going to shit, there is nothing wrong with it at all. People shouldn't just attack people like you do dan, or that black32 im so cool guy.

You didnt tell me about the hose already all you said was the stuff you have doesnt fit and I doubt they make the OCC hose big enough to fit over those ports so I am going to have to go and get soemthing that will.

Paully.....

I will say it again the hose i have at my home came off the rex.....its too small.

Now like i said before i dont have that little breather hose on mine i have oil catch can hose on both breathers. So yes they do make it that big. Go to autobarn would you like there number and address. If you like i will go and take a photo just to make sure you understand that yes they do make it and yes it does fit just not the old hose i have off the rex.

dan you misunderstand completely. and no i have been told generic hose from those places wont be good for the breather as oil braeks down the inside of the hose. depending on what people have ill ask.

dan you misunderstand completely. and no i have been told generic hose from those places wont be good for the breather as oil braeks down the inside of the hose. depending on what people have ill ask.

The heater hose stuff works perfectly fine for quite a bit longer than you would expect. I've had some on mine for a good 2.5years now; yes it has recently started to feel a little soft but its not stuffed just yet. :thumbsup:

Look in the sticky misc workshop listing as there's a few rubber places listed in there that sell the 'correct' stuff that you are after.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...