Jump to content
SAU Community

Batteries Going Flat.

Raul

By Raul,
in General Maintenance

 Share

Recommended Posts

Raul Explorer

Raul

Posted
Posted

Hey,

posted here about a week ago about my alarm playing up. Turned out it was a dead battery, so i then got a new battery and has been all good until now (a week later). This has lead me to suspect that something is running my batery flat! couldit be that the workshop that installed my alarm installed it wrong and may that be the cause of my batteries being sucked dry? Before the alarm was installed it was fine.

Also it has been suggested that the alternator may be the problem, however wouldnt their be a dash light going off if this was the case?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/148508-batteries-going-flat/
Share on other sites
wilch Grand Master

wilch

Posted
Posted

No dash light for the alternator.

To test if the alternator is stuffed:

- Grab a multimeter. Put it across the positive and negative terminals on your battery with the car off. Make sure it reads about 12v.

- Turn the engine on. Do the same thing. Put the multimeter across the positive and negative terminals on your battery. It should now read about 14v give or take a 0.5v or so.

- If it still reads the same as when the engine was off then your alternator is dead.

The other thing that could be wrong is that your battery is on it's last legs. How old is it?

If it's not the alternator or the battery then it has to be the alarm install. In which case you should take it back and get them to check what they've done. It could be something as simple as an incorrect ground.

I had an internal piezo screamer installed in my car that I had to remove due to it constantly draining my battery. It was a case of the alarm sending a ground signal instead of sending 12v to set the siren off. With the piezo screamer not being grounded properly and being connected to 12v, this meant that the battery was being drained constantly.

blind_elk Grand Master

blind_elk

Posted
Posted
- Turn the engine on. Do the same thing. Put the multimeter across the positive and negative terminals on your battery. It should now read about 14v give or take a 0.5v or so.
Rev the engine to around 2k. If the volts increase with revs, the regulator is cooked, and will result in your battery being overcharged. Overcharging will kill it.
Raul Explorer

Raul

Posted
  • Author
Posted

Jsut got my hands onm a multimeter, and the battery was reading 6 so i jump started it and it read up to 14v constant. Even when reving the engine it was constantly on 14v.

So can i assume that my alarm that was installed at one of SA's reputable wokshops has been installed incorrectly? If so i wont be happy as i have had so many headaches with this alarm its not funny.

Cheers for the replies guys

blind_elk Grand Master

blind_elk

Posted
Posted
14v for a running motor is fine. It will go down to around 12v though after a short time when running.

Check the alternator output as wilch and blind elk said. It shouldnt cost too much to have it rebuilt, or just buy a new one.

Switch everything off. Switch the multimeter to amps, remove the +ve cable, and measure the amps between +ve battery terminal and the +ve cable. Reconnect battery. Then remove each fuse in turn, and measure if any amps across each fuse slot - that will tell you which circuit is drawing the current that is killing the battery.
Raul Explorer

Raul

Posted
  • Author
Posted (edited)

Hey,

Just to clarify ont he multimeter where should i be leaving teh knob to test the fuses?

Well i had the knob turned on the icon with an arrow and a '+' sign nextg to it and it gave me a reading of around 5-6v between the batterys positive terminal and positive cable. Then in the fuse panel under the drivers side dash, the fuses under ign had a reading of around 4-5v.

Any suggestions? Basically i want to pinpoint where the power is getting sucked as i want to know whether or not it was the alarms installation fault or not.

Cheers

Edited by Raul
blind_elk Grand Master

blind_elk

Posted
Posted

You are measuring VOLTS, you need to measure AMPS (ie current). Volts are measured in parallel with the device you are testing, amps are measure in series.

It will probably vary with the design of the multimeter you have - mine has A (makes sense) near the various scale settings.

And you only need to check the fuses if you find a significant current flowing from the battery.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...