Jump to content
SAU Community

Stagea Tie Rod Replacement, How

kiwi_rock

By kiwi_rock,
in Four Door Family & Wagoneers

 Share

Recommended Posts

kiwi_rock Rookie

kiwi_rock

Posted
Posted

Hi guys,

I've got a '96 RWD stagea, about 123,000K's it's up to now, thrown about 40,000 on in the past year and a half.

I've been rotating the tires and found some grease lurking around and tracked it down to a stuffed boot on the ball joint of the drivers side tie rod.

I'm thinking about just replacing the entire tie rod ends on both side as the parts store reckon about $25 per replacement kit.

So I've removed the castle nut and with some downward pressure gave the casting on the hub a swift belt with a hammer to try and loosen the tie rod incase it's still reusable. There doesn't appear to be any play but I can fell some gritty dirt in the joint.

Anyway, the tie rod end refuses to slip out, any other ideas of a nice way to remove it without stuffing it?

BTW, I'm no mechanic, but I'm technically minded. So thought I'd give it ago and since I've got the time over the holidays before I need it in 2 weeks to go to the airport a few hundred K's away and the local mechanics are fully booked during that time.

But I can slip in for a wheel alignment once I've done the work myself.

Thanks for any help, kind regards.

Gavin.

Link to comment
https://www.sau.com.au/forums/topic/148868-stagea-tie-rod-replacement-how/
Share on other sites
Stinky Rooster Grand Master

Stinky Rooster

Posted
Posted

If you have 2 hammers, I have always found it useful to put 1 against the side of the eye (that the ball joint) is located in, and give the other side a few hard taps with the other hammer. It sometimes helps to "wake up" the lock on the taper and help loosen it when you knock it from the top. This problem occurs with every ball joint I have ever done so you are not an orphan here mate! :P:):iluvff:

mr manfringinsen Contributor

mr manfringinsen

Posted
Posted

There is a tool you can buy which looks like a large two prong fork which tapers down to a point. You put the fork between the steering arm and ball joint and belt the end with a lump hammer, like a wedge it forces the ball joint out. It saves a lot of heartache. I don't think there is a spare parts shop I've been in that wouldn't have one of these on the shelf. It will wreck the rubber boot on the ball joint when you remove it but it sounds like your ball joint is shot anyway.

The tool comes in two or three sizes.

Appealing Proficient

Appealing

Posted
Posted

There is also another tool for this, it's called a ball joint splitter, (for obvious reasons). Should be available from Repco, or Coventry's. It has a fork that sits over the ball joint and a bolt that is positioned onto the top of the taper, you just keep doing it up until either the ball joint gives or the tool breaks! :) Tow hammers works really well, causes slight ovality to the hole that the taper sits in thereby popping it out. A combination of the above is sometimes required. I also have a fork type and find this a useful tool, (not just for ball joints). I should hope that by the time you get all this info you have done the job. haha :P

  • 2 months later...
overpowered Enthusiast

overpowered

Posted
Posted (edited)

get a 2 arm pulley like they use for harmonic balancer removal (except they use 3 arms and are way way bigger) and it will come out easy as hell, ive removed mine about 10-15 times everytime the motor comes in and out so its definately a tool to make it easier, and belting it with a hammer even with the nut on will just damage the nut head and wreck the threads,

those ball joint splitters are bloody useless too ive got one and it didnt work at all.

if u cant understand what tool im talking about then let me know and ill take a pic of it for you :domokun:

hope it helps mate

*edit* whoops just noticed the post is old, sorry :P ill leave the info for future reference for anyone else needing the do the job :D

Edited by overpowered
jbonevia Contributor

jbonevia

Posted
Posted

i always screw an old wheel nut onto the thread and then bash the wheel nut with a hammer - works every time and doesnt damage the tie rod. Use a wheel nut that has a covered end on it though or dont screw it on all the way or you will damage the tie rod thread and be unable to unscrew the wheel nut!

stasis Mentor

stasis

Posted
Posted
Yudi, PM me your VIN number and I'll tell you what the Nissan part number is, I assume it would be the same as the RS model series though?

Ok thanks cyrus but will have to wait till when i get back to Oz. im overseas at the moment. thanks again

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • myrbgivesmeheadaches
      RB25DET NEO Cylinder Head

      By myrbgivesmeheadaches · Posted

      Did this end up working? Did you take some pictures?
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...