Jump to content
SAU Community

6k

RPR33

By RPR33,
in Engines & Forced Induction

 Share

Recommended Posts

Drivebai Community Regular

Drivebai

Posted
Posted
These injectors, are they made by Deatchwerks? is it lik saying im installing nismo injectors, instead im installing Deatchwerks injectors? has anyone used them? what are they lik? cos i lik the price.......

I have these injectors.. works fine for me. i have 240rwkw and max duty cycle i seen is 68%

i highly recommend them, they are high flowed injectors.

They are straight fit.. just like nismo.. fit on stock fuel rail, and comes with flow report of each injector.

Alot of Drag supra's in the states use them

check out their website..

http://www.deatschwerks.com/

Also if you do a search on deatschwerks on any car forum, people seem to say good things about them..

just stay away from Venom injectors.

Link to comment
https://www.sau.com.au/forums/topic/148987-6k/page/2/#findComment-2780025
Share on other sites
Adz2332 Grand Master

Adz2332

Posted
Posted
I have these injectors.. works fine for me. i have 240rwkw and max duty cycle i seen is 68%

i highly recommend them, they are high flowed injectors.

They are straight fit.. just like nismo.. fit on stock fuel rail, and comes with flow report of each injector.

Alot of Drag supra's in the states use them

check out their website..

http://www.deatschwerks.com/

Also if you do a search on deatschwerks on any car forum, people seem to say good things about them..

just stay away from Venom injectors.

What size injectors do u have? Im aming at 250kw at the wheels

Link to comment
https://www.sau.com.au/forums/topic/148987-6k/page/2/#findComment-2780033
Share on other sites
Drivebai Community Regular

Drivebai

Posted
Posted

only had them in for a couple of months. no problems with them so far.

My tuner said he really liked them.

It was about $600 delivered.

you can also get some cashback offer too if you send your old injectors to Deathscwerks so it works out to be even cheaper.. i didn't do this though as i damaged the old injectors trying to pull them off the rail.. haha

Link to comment
https://www.sau.com.au/forums/topic/148987-6k/page/2/#findComment-2780057
Share on other sites
Adz2332 Grand Master

Adz2332

Posted
Posted
only had them in for a couple of months. no problems with them so far.

My tuner said he really liked them.

It was about $600 delivered.

you can also get some cashback offer too if you send your old injectors to Deathscwerks so it works out to be even cheaper.. i didn't do this though as i damaged the old injectors trying to pull them off the rail.. haha

ok cool was jus wondering how long they will last for. How long do injectors useally last for

Haha damn, i might be careful taking mine off then haha.

Link to comment
https://www.sau.com.au/forums/topic/148987-6k/page/2/#findComment-2780062
Share on other sites
Drivebai Community Regular

Drivebai

Posted
Posted

I can't see why they would not last, my stock injectors were fine ( well not after i pulled them out) and i had about 180,000km on the clock.

Just keep an eye on max duty cycle on your PFC controller.

Bear in mind that it will show overall injector duty cycle not individual.

They flow test the injectors thoroughly and my injectors had something like 0.02% variance. Each injector is marked with a number which corresponds to the report.

yeah careful taking out your old ones, you can even pack them in the box that your new injectors came in and send them back to them.

Link to comment
https://www.sau.com.au/forums/topic/148987-6k/page/2/#findComment-2780074
Share on other sites
Adz2332 Grand Master

Adz2332

Posted
Posted
I can't see why they would not last, my stock injectors were fine ( well not after i pulled them out) and i had about 180,000km on the clock.

Just keep an eye on max duty cycle on your PFC controller.

Bear in mind that it will show overall injector duty cycle not individual.

They flow test the injectors thoroughly and my injectors had something like 0.02% variance. Each injector is marked with a number which corresponds to the report.

yeah careful taking out your old ones, you can even pack them in the box that your new injectors came in and send them back to them.

excellent thanks for that, good info. cheers

Link to comment
https://www.sau.com.au/forums/topic/148987-6k/page/2/#findComment-2780078
Share on other sites
Drivebai Community Regular

Drivebai

Posted
Posted
i'm in.... I'll give them ago

Cheers

So a guess mods rather than rebuild?

I went the mods route.

I got a fair few kms on my car.didn't know if i should sell it or mod it. took it to my tuner and he put the car on the dyno did som test on it and he said everything is healthy and if he was me he would keep the car.

i said i'm worried about the kms on the car and if i mod it something mite go wrong.. he said kms aren't everything you can have a 60,000km car with a bad motor and have a 200,000km car with a much more healthy engine. then i asked him if i should do rebuild first before modding it.. and he said what for? as long as the tune is good and safe you shouldn't have any problems.. alot comes down to the tune.

If you aren't chasing that much power then no need to rebuild what could be a very healthy engine.

anyway just my thoughts.

good luck with your decision.

Link to comment
https://www.sau.com.au/forums/topic/148987-6k/page/2/#findComment-2780298
Share on other sites
khunjeng Veteran

khunjeng

Posted
Posted
I went the mods route.

I got a fair few kms on my car.didn't know if i should sell it or mod it. took it to my tuner and he put the car on the dyno did som test on it and he said everything is healthy and if he was me he would keep the car.

i said i'm worried about the kms on the car and if i mod it something mite go wrong.. he said kms aren't everything you can have a 60,000km car with a bad motor and have a 200,000km car with a much more healthy engine. then i asked him if i should do rebuild first before modding it.. and he said what for? as long as the tune is good and safe you shouldn't have any problems.. alot comes down to the tune.

If you aren't chasing that much power then no need to rebuild what could be a very healthy engine.

anyway just my thoughts.

good luck with your decision.

I'm no guru but it seems u can make good power with a rb25 motor in good condition without the need for new internals..I have been running 250+ for some time with stock internals...I did a compression test recently cos I was bored and everything was the roughly the same as when I got it tested 1 year ago before the mods...

verdict...its ok.

Link to comment
https://www.sau.com.au/forums/topic/148987-6k/page/2/#findComment-2780553
Share on other sites
RPR33 Community Regular

RPR33

Posted
  • Author
Posted (edited)
Hey mate what state u in?

Also what time frame are u looking at doing this over?

I'm in vic mate you? thinking anytime from now untill late jan early feb!

they sound like a good deal..

Edited by RPR33
Link to comment
https://www.sau.com.au/forums/topic/148987-6k/page/2/#findComment-2780857
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Manur33
      Rb25det coil loom wire identification

      By Manur33 · Posted

      Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • davemoto63
      Stagea choice's which model??

      By davemoto63 · Posted

      Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • davemoto63
      Noobie Stagea owner..

      By davemoto63 · Posted

      Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...