Jump to content
SAU Community

Going For Fulls - Dqt @ Rta Nsw

satanic

By satanic,
in New South Wales

 Share

Recommended Posts

MK2 Experienced

MK2

Posted
Posted

It's been a few years... :)

Guess rev it too about 4-5k, drop it and flat shift from 2nd-3rd, clutch kick that bitch at 80km/h into the corner to get the back end out, power on, opposite lock and use the hand brake if you need it.

Lots of smoke and speed, judges like smoke.

TokyoTaxi Veteran

TokyoTaxi

Posted
Posted

Just stumbled across this thread and F*** do I feel old now !!!

Stan, I got my license 1 year before you were born !! :dry::)

Anyway, hope you got it ! ( and keep it ) :P

( and no, there won't be any "back in my days" comments from me ).

satanic Grand Master

satanic

Posted
  • Author
Posted

LOL at all the comments since yesterday...

UPDATE:

* Stan is now a REAL driver - WOOHHOOOOO!!!

* Thank you to all who supported and gave advice :D

WHAT HAPPENED:

* Got there real early with the manual in hand (just like Beer Baron suggested, looked real nerdy and they bought it :))

* Got into the test

* They hit me with three statistics questions which totally threw me off but I guess I just picked the most logical and "safe" option.

* All those touch the screen scenarios were really easy, answers were obvious. I just made sure to touch the screen twice on every instance that I was supposed to - just to make sure.

Anyways, see you on the road - keep it safe - remember, over 90% of all accidents are caused by human error!

PS: Feels really good not to be a P-Plater anymore :)

oweban Grand Master

oweban

Posted
Posted

I failed my fulls the first time around, had a massive go at them (the answer was NOT to look as far ahead as possible, but only 10 seconds or something, which contradicts the learners book), and they let me resit it again in 30 mins. Got it that time. Then didn't have enough money to get the 3 year license. :)

But good onya dude :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The king 2.0
      Nissan fuga 450gt android screen

      By The king 2.0 · Posted

      Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • dbm7
      Automatic Power Button Light Flashing

      By dbm7 · Posted

      Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Duncan
      R34 Plug Identification

      By Duncan · Posted

      Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...