Jump to content
SAU Community

Powerfc Tune And Boost?

evil_weevil

By evil_weevil,
in Engines & Forced Induction

 Share

Recommended Posts

evil_weevil Grand Master

evil_weevil

Posted
Posted

Hi guys,

Getting my car tuned late next week, and so far its just ya 33gtst with "basic mods" using a turbosmart single stage boost controller (flick between standard 7 and its meant to be set to 10psi but spikes 50% of the time!) and Im thinking - should I ditch the turbosmart b/c and go back to the normal solonoid to prevent the thing from spiking and causing issues, or as its being tuned (2-3 day tune) will it be alright?

At the moment the car is running like crap and I just cant wait for the tune to stop all these bugs.

But my main concern is boost. is 7psi stock going to be sufficient? Or should I use the turbosmart b/c and just keep it at the one setting?

Or somehow rob a bank and buy an EBC for minimum 500?

Cheers guys,

Chris

Link to comment
https://www.sau.com.au/forums/topic/149726-powerfc-tune-and-boost/
Share on other sites
siddr20 Grand Master

siddr20

Posted
Posted

You want EBC-- those profec spec B's are 390 to your door step!! look in trader section!!

Otherwise see what the tuner says!! Buy another cheap bleed value and if there any issues with your turbosmart while tuning, ask your tuner to use the new bleed value and see if that works..

If its still spiking, get a ebc..

But see what your tuner says first..

series2r33 Collaborator

series2r33

Posted
Posted

I got my eboost 1 for $550 brand new. U might be able to get one cheaper second hand or off ebay. Its got 3 boost settings which is perfect since my cars main priority is road use, but the 3 preset settings u can jump between at the press of a button makes its easy if u wanna really give it a boot or take it to the drags. I've got mine set at 8 - 10 and 14 psi. I cant see the point of spending the extra money and getting an eboost 2 with the 8 boost settings unless your cars just for drag racing since its got all that extra jazz in there to take care of that kind of stuff.

_8OO5TED_ Mentor

_8OO5TED_

Posted
Posted (edited)

it will take a week to confirm a purchase and transfer the money, especially with a weekend in between. you are gonna have to get something local champ. perhaps loan a good working bleed valve from someone until your nengun purchase comes in?!

Edited by _8OO5TED_
Birnie Veteran

Birnie

Posted
Posted (edited)

If you aren't running too much boost, it probably is best just replacing your bleeder.

I'm on 12psi and PowerFC.

It fluctuates but i can't tell from the driver seat.

Here's the curve......

post-5823-1167850342.jpg

Edited by Birnie
Munkyb0y Grand Master

Munkyb0y

Posted
Posted

why dont you go with the turbotech bleed valve ($22), and set your desired boost using a boost guage. then the tune will be right for your boost setting, and you can use whichever boost controller you want later, just set it at the same boost level.

Kennedy Mentor

Kennedy

Posted
Posted

Dont be rushed into a EBC just because of your tune next week. Get a turbotech for now and worry about your EBC later. EBC's cost quite a bit so you don’t wont to be rushed into a decision solely based on delivery times.

I have a spare turbotech if you wanna borrow it for a month or so as I have recently upgraded to an greddy e-01 so I can pull the chics like Paul Walker. PM me if you wanna borrow it

benl1981 Grand Master

benl1981

Posted
Posted (edited)

Hey Chris!

You will not get the benefit of the electronic type!!

Save your money. The $20 one works fine for up to about 12psi or more.

Or even a small orifice piece that you replace your solenoid with will give you steady 10psi (If the right size bypass hole). It's bypasses enough air to maintain 10psi..

Only when you upgrade the turbo consider a more elaborate boost controller.

Edited by benl1981
  • 2 weeks later...
YLD-CHLD Collaborator

YLD-CHLD

Posted
Posted (edited)

I already had the Power Fc installed so all that was needed was to get an electronic solenoid hook it up to the standard solenoid plug then attach the signal & actuator hoses.

Then attach a MAP(3bar) sensor to the input on the power fc.

Haltech sell the solenoids for about $120

Then dial in your levels on the hand controller duty cycle & pressure.

& make sure u have the correct cable/loom

Edited by YLD-CHLD

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • joshuaho96
      Ethanol Content Sensor - Always at 11%?

      By joshuaho96 · Posted

      The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • GTSBoy
      R34 Skyline climate control unit transistor

      By GTSBoy · Posted

      It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...