Jump to content
SAU Community

pRoBleM

croat

By croat,
in General Automotive Discussion

 Share

Recommended Posts

croat Mentor

croat

Posted
Posted

I have this problem when i rev my car and its not in gear the revs come back down and fall below the normal idle level. The car pretty much stalls then pics itself up again and idles normally. same thing if i take of fast then put the clutch in. anyone had this problem? Or know what is wrong?

Thanks...

Link to comment
https://www.sau.com.au/forums/topic/14981-problem/
Share on other sites
Al Grand Master

Al

Posted
Posted

Read about this in HPI mag, problem is worse if you have a bigger turbo, should not really happen if engine is stock.

As you accelerate or rev, the butterfly in throttle body is open, once you let go of the accelerator the butterfly shuts. Due to the suction of air under acceleration, some of the air bounces off the butterfly and goes back through your a/f meter. This cools the wires in the a/f meter tricking the computer into thinking the engine requires more fuel, thus floods the motor for a split sec. HKS have a device to overcome this problem, not sure of the name.

Before doing anything, make sure the a/f meter is clean.

Link to comment
https://www.sau.com.au/forums/topic/14981-problem/#findComment-304205
Share on other sites
Al Grand Master

Al

Posted
Posted

The ecu is programmed for a plump-back, this floods the motor for a split second, to compensate for the lack of air.

Best bet is to put the stock BOV on and test it. Could solve all your problems, and make your car more enjoyable to drive and legal.

Link to comment
https://www.sau.com.au/forums/topic/14981-problem/#findComment-304232
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...