Jump to content
SAU Community

Recommended Posts

well when im on boost i get some blue smoke. on idle and low rev driving its fine.

oil pressure is fine too.

im not sure if its my rings or my valve stem seals.

ive completely ruled out the new turbo as ive checked the cooler pipes etc.

ill be doing a compression test tomorrow to see if its my rings (mind you ive rebuilt the motor with NEW rings).

what should i be looking out for if its my valve stem seals?

Link to comment
https://www.sau.com.au/forums/topic/150005-blue-smoke-out-of-exhaust/
Share on other sites

sorry to ask this question, i am curious how you guys find out that smoke is blowing out of the exhaust while you are driving? especially on boost.

revision mirror dude.

your turbo can still be burning oil without traces in your cooler pipes...the rear seal in your turbo could be gone. say movement in your turbo shaft can be pulling forward under boost so that allows oil to slip out the seal on the exhaust side. hence only on boost. idle the motor and take the oil cap off and feel for excessive blow by.

you cant really 'check' valve stem seals. you only know it was them when you change them and the smoke stops. spent hours on a 4g63 changing the valve stem seals only to find out that it was the turbo seals.

Edited by Ryanrb25
orh ok. thanks. i am wondering how to spot the problem if i happen to encounter one.

cheers

do you have a catch can???

also is it plumbed back into the inlet and or turbo ducting?

take off your rockers and check if the breathers are clogged in the rocker cover baffles,

i had similar problem after i built my engine, new turbo everthing, was blowing shit loads of smoke(blue)

found to be cause the breathers were blocked due to old engine having so much blo by..

hope this helps

Jeremy

thanks for the replies guys.

im going to compression test it today, ill take it for a drive and see if its doing it today, its a bit on and off sometimes.

ill check my breather pipe after the drive too.

any other symptoms??? misfiring... check out your spark plugs too (stupid to say i guess coz you take em out when you comp test anyway) if theyre fouled or very clean

how long since the rebuild

After my engine was built, it was doing similar things and it came down to 2 of the rings were leaking. They said it was something to do with the type of rings that were used, they either seat properley and you never have a problem or they don't and they leak. They replaced all the rings with new ones and haven't had a problem since.....

i have heard the same thing about the valve stem seals

your having the exact same symptoms as i did,

check your breathers in the rocker covers,

take them out and soak them in kero,then let them dry then put it all back in

Edited by DVS32R
the rings i used were brand new from nissan. they were placed on the right angles too (i.e. not on the thrust side of the piston).

ah fair enough, I dun have factory ring there something else. Can't think of what there made of off the top of my head....

Yeah valve stem seals going is usually evident by what I would call back off blow by.

I'd be thinking of rear turbo seal possibly. This happened to me recently.

Are you sure it's blue and not black from running rich? (Have to ask. :dry:)

Is it definitely coming OUT of the exhaust? I mean, some oil could be dripping ONTO it from somewhere possibly, although you would probably smell it when idling.

Blue under hard acceleration sounds like rings to me, of course turbo seal will do the same thing, stemseals will smoke downhill of throtle.

Don't forget slightly worn or not bedded in rings won't always show on a compression test because the oil blocks the gap and you could have perfect comp. Actualy a slightly worn engine ( bottom end, not worn valves) could have higher comp due to the fact that you may have carbon on the top of the pistons.

Do a leakdown test , then you will know for sure if you are loosing comp.

Blue under hard acceleration sounds like rings to me, of course turbo seal will do the same thing, stemseals will smoke downhill of throtle.

Don't forget slightly worn or not bedded in rings won't always show on a compression test because the oil blocks the gap and you could have perfect comp. Actualy a slightly worn engine ( bottom end, not worn valves) could have higher comp due to the fact that you may have carbon on the top of the pistons.

Do a leakdown test , then you will know for sure if you are loosing comp.

thanks mate, ill get a leakdown test done.

is there any way to check if its the turbo?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..   
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...