Jump to content
SAU Community

Electrical Problems

Chegs

By Chegs,
in General Maintenance

 Share

Recommended Posts

Chegs Contributor

Chegs

Posted
Posted

Hey guys, i have been having an intermittent problem with my r33 gtst for a few weeks now. when driving along, it just stops firing on all cylinders and dies, but picks up again before it stalls. i have just replaced the coils and plugs, so i think it may be the crank sensor. has anyone ever experienced a similar problem before?? its really bugging me and any insight as to what may be wrong would be greatly appreciated :laugh:

Thanks, Bill

Link to comment
https://www.sau.com.au/forums/topic/150184-electrical-problems/
Share on other sites
kiz_baby Apprentice

kiz_baby

Posted
Posted

I too am having the same problem. My car is an R33 S2 GTST Automatic. It has been stalling while idling at the lights and in some cases takes a while to start after stalling. I have also noticed revs dropping significantly while driving and the accellerator feeling sticky when this happens. Stalled as i was taking off from the lights last night.

Car has been with the mechanics twice who have still not figured out the problem. First time in, they changed the oxy sensor which made no difference at all, 2nd time in they found a fault with the wiring harness for the air flow meter and fixed. Car ran beautifully after this for 3 to 4 hours before stalling again in idle and then 30 mins later, stalling on take off from the lights as mentioned.

My mate was with me and thinks but is not sure that it could be the crank angle sensor and from reading topic "Sticky: Missfire Boost.." it seems other people have had this problem and was solved by changing the crank angle sensor.

My advice, if it's only just started to happen, get it looked at quickly because it gets worse quick.

mjones Collaborator

mjones

Posted
Posted
I too am having the same problem. My car is an R33 S2 GTST Automatic. It has been stalling while idling at the lights and in some cases takes a while to start after stalling. I have also noticed revs dropping significantly while driving and the accellerator feeling sticky when this happens. Stalled as i was taking off from the lights last night.

Car has been with the mechanics twice who have still not figured out the problem. First time in, they changed the oxy sensor which made no difference at all, 2nd time in they found a fault with the wiring harness for the air flow meter and fixed. Car ran beautifully after this for 3 to 4 hours before stalling again in idle and then 30 mins later, stalling on take off from the lights as mentioned.

My mate was with me and thinks but is not sure that it could be the crank angle sensor and from reading topic "Sticky: Missfire Boost.." it seems other people have had this problem and was solved by changing the crank angle sensor.

My advice, if it's only just started to happen, get it looked at quickly because it gets worse quick.

i'd change air flow meters over!!

Godzilla32 Veteran

Godzilla32

Posted
Posted

LOL an engine will run without an oxygen sensor signal (though not as economically) so there is no way that would fix a stalling problem.

A missfire is not the same as what your saying you have. So i wouldnt go on anything said in the missfire thread. A common oversight people seem to have is if they have the same symptoms as another person thay automatically think its the same fault! Never assume this as 90% of the time it wont help you.

Deren

kiz_baby Apprentice

kiz_baby

Posted
Posted
LOL an engine will run without an oxygen sensor signal (though not as economically) so there is no way that would fix a stalling problem.

A missfire is not the same as what your saying you have. So i wouldnt go on anything said in the missfire thread. A common oversight people seem to have is if they have the same symptoms as another person thay automatically think its the same fault! Never assume this as 90% of the time it wont help you.

Deren

Car was originally missfiring as well and revs dropping significantly while in motion. Now I just need to work on the stalling problem. I am also running .95 - 1.02 bar. I will check the coils but I would be very appreciative if anyone has any ideas.

kiz_baby Apprentice

kiz_baby

Posted
Posted

Thanks guys! Changed airflow meters over and so far running like a dream and better than before. I had taken this car to the mechanics 3 times before they finally said it was the AFM.

I do not recommend anyone going to Sumo Performance in Nunawading, Vic (Kamikaze's mechanics) as they had the car for over 4 weeks and couldn't nail the problem. I posted my problem here and got a response same day which was accurate and correct. Thanks again to all.

Chegs Contributor

Chegs

Posted
  • Author
Posted

Hi everybody, thanks for the help. i took the plug out of my afm, resoldered it and car goes like a dream. I too thought it was the crank angle sensor, but had the same symptoms of stalling and funny idle. I replaced all the coils and plugs but it would just cut all power for a few seconds and then come good again. instead of changing the afm, pull the plug off, unscrew the plug body on the afm and prise off the top cover. resolder the 5? joints and reglue on top cover and screw housing back in, worked fine for me and cost nuthin.

Thanks.

kiz_baby Apprentice

kiz_baby

Posted
Posted
Hi everybody, thanks for the help. i took the plug out of my afm, resoldered it and car goes like a dream. I too thought it was the crank angle sensor, but had the same symptoms of stalling and funny idle. I replaced all the coils and plugs but it would just cut all power for a few seconds and then come good again. instead of changing the afm, pull the plug off, unscrew the plug body on the afm and prise off the top cover. resolder the 5? joints and reglue on top cover and screw housing back in, worked fine for me and cost nuthin.

Thanks.

Sounds like we may have had very similar problems. My wiring harness had already been fixed, plugged my AFM into another car and found it to be no good.

Chegs Contributor

Chegs

Posted
  • Author
Posted

I found through a bit of searching on sau that cars with pods seem to have the afm break quite frequently due to vibration. when i removed my plug, the solder joints were not even joining, so much so that i just pulled the plug out of the afm. Its a bit fiddly to get that silicon off the afm, but its cheap and easy. ive since realised that is why my car has been running horribly for months. If you do a search on air flow meters you will turn up something helpful.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      You know how your car rolled through a fence in your last jacking escapade? Scissor jacks increase the likely hood of that sort of thing happening immensely!
    • Piggaz
      Jacks that fit under GTR lips that can reach the subframe?

      By Piggaz · Posted

      http://calfinn.com.au/product/1500kg-standard-trolley-jack-cj-2t-c/1500kg-standard-trolley-jack-cj-2t-c   I have this and fits under a S3 33 GTR with no issues. Purchased in 2009 and not one issue. It was $950 back then. Not cheap but something so important isn’t worth cheaping out on.
    • MBS206
      R32 GTST - 600KW+ RB28/CD009 Build

      By MBS206 · Posted

      Just trying to get my head around this. At 5psi of boost, you turn on your wmi pump, and then you're using a 3000cc injector, to allow flow upto the actual engine, where you have your 6x200cc injectors and a 500cc injector. If the above is correct, what advantage are you obtaining by having the 3000cc injector blocking flow, is this just incase a line breaks between that injector and the motor you can stop flow immediately? Or are the 6x200cc and 500cc less injectors and just spray nozzle?
    • f00stx
      Intro/R33 owner

      By f00stx · Posted

      Welcome! New member myself, but I had an R33 back in 2002. Best advice I could give, based on my experience: if you're running the factory turbo, be very conservative with boost. I made the mistake of just fiddling around with the boost controller and cranking the boost for fun, and the end result was my intake pipes popping off frequently from the constant deluge of oil that was being blown into the recirc by the stressed-out turbo, which itself was siphoning oil from the engine and farting it out both sides of its centre bearing (or something to that effect). If I could do it all again, I would have gotten a new turbo and had a tune dialled in professionally and then just left it alone! Funny you mention the metal shavings in the gearbox, as I had the same thing - the probe plug (magnetic drain plug, essentially) would come out caked with shavings. At least it was doing its job. Not sure if that's just sacrificial wear and part of the deal, or if my gearbox was shagged, but I wasn't abusing it. Enjoy the R33 - they're a dying breed, and if they weren't $35k+ on CarSales in Queensland, I might have picked up one of those again, instead of the 370GT I own now (though I'm loving the 370GT, that big 3.7L V6 just hits different).
    • f00stx
      Second time Skyline owner (R33 GTS-T and now a V36 370GT)

      By f00stx · Posted

      Howdy folks. I owned an R33 back in 2002, which was thoroughly beyond my capacity (financially speaking) to maintain/insure, so we parted ways in 2004. Fast forward 21 years (to literally yesterday, in fact) and I'm now the proud owner of a 2007 V36 370GT. I'm happily surprised by how much power the VQ37VHR makes, compared to the RB25DET, considering the latter is turbocharged. I had planned to add a turbo at some point but I'm on the fence about whether I'll even need it (though I do love the sudden onset of extra torque). Any other 370GT owners around the traps, I'd love to hear about your experiences with this car (good and bad).
×
×
  • Create New...