Jump to content
SAU Community

Recommended Posts

Below is a list of everything i have for sale, link provided that has pics. I can provide more/better pics if needed.

All items are in Townsville, Queensland.

Contact me at packy @ racecrewz.com

or sms 0411 41 3255

thanks

RaceCrewz.com

Acer CD/RW drive, good condition - $5

R33 turbo front and rear discs - $150

True Hybrid top intercooler pipe - $50

Aluminium 2.5inch

True Hybrid bottom intercooler pipe - $50

Aluminium 2.5inch

Alloy Cone Shaped gearknob, suit any nissan thread - $5

Standard RB25det air flow meter - $100

Standard RB25det boost control solenoid - $20

R31 split headlights in good condition- $100

also comes with support bar with brackets

Standard R33 Series II Manual ecu - $150

Standard RB25det Turbo injectors - side feed 340cc $120

Standard RB25det bov $20

Standard R33/RB25det turbo exhaust cat back $50

Standard RB25det crossover pipe $60

Standard R33/RB25det fuel pump assembly $60

Standard R33/RB25det rear muffler - $30

Standard R33/RB25det coil packs Series II - $75 each

or $300 for all 5

Standard R31/RB30e auto gearbox - $5

Standard RB30e Bosch Coil pack - $10

perfect working order

Standard RB30e Bosch Distributor - $25

perfect working order

Standard RB30e head - $20

cam gear, valves, rockers all included

Standard RB30e inectors and rail - $20

with wiring loom(although cut a foot away from plugs) and plugs

Standard RB30e inlet manifold and plenum - $20

Can be cleaned and painted for extra cost

Standard RB30e water pump and power steering pulleys - $1

Standard RB30e starter motor - $5

Silicone reducer 4inch to 3inch - $20 (rrp $45)

brand new, bright blue

Simota air filter 3inch fitting - $20 (rrp $39)

Brand new

RB30e idle control valve - $5

R31 Dash switches and clock etc - $10 the lot

R33 coupe boot linings - $90

R33 under bonnet liner - $15

RB30e exhaust manifolds x2 - $20 for both

RB30e cam cover - $100

R33 Aircon climate control unit - $15 (auto and off buttons are loose)

Unifilter Ram pod to suit R33 air flow meter - $30

RB30e inlet pipe - $5

Makita 14.4volt 1.3Ah batteries for cordless drill x2 - $50 for both

Agfa flatbed scanner - FREE !!!!

Microsoft Encarta 2006 unopened/brand new - $5

Zoo Tycoon 2 game unopened - $5

Logitech Multimedia keyboard - $5

Teac Standard definition set top box - Used for a year $40

Edited by Packy
Link to comment
https://www.sau.com.au/forums/topic/150751-r31-and-r33-parts-for-sale/
Share on other sites

  • 1 month later...
  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For fuelling the Haltechs have O2WB fuel controllers. Very useful for helping tuning VE and correcting for *small* mistakes. Of course if your injector/cam/trigger/sensor data is just wrong (or for a GTT which is not a GT) then you will get impossible reactions to things. I am sure you know this already but the reason people don't typically put haltechs (or any Aftermarket ECU) on GT's is because there's practically no real gains to be had - So this knowledge won't be commonplace.
    • Can someone tell me if the cracks seen in the rear sway bar bushings in these photo's is unacceptable from a roadworthy point of view?  
    • Shouldn't need a "base map" for anything other than guidance to ignition tuning. You just need the engine capacity right, the injector size right, and something, almost anything, for a VE map. On an NA engine, fuelling is almost completely a function of load signal & rpm. It should run and drive with a completely flat fuel map. It will be too lean under load, but that's easily fixed. We used to tune all ECUs without any base map. There were no such things (until someone had tuned a near stock engine on one, and then they had a "base map".
    • What did you actually buy/how much did it cost? When I got mine in like.. 2017...? 2019? the aim was to run Torque for gauges via ODB2 and things like Track Addict/Laptimers/Dashcam/Reversecam/Spotify etc. Mine never broke, but I wonder if you've got the same needs (it sounds like it). Cause I liked the idea of being able to do anything with it. That said, yours also cost 3x the cost of what I spent so... food for thought.  
    • For me there is a massive difference in manufacturer or big brand crippled android (Sony, Kenwood etc) vs the sort of thing I've installed here, which is basically just a tablet in DIN form factor with open Android, and the other model of course is mirroring - Android Auto/Carplay. I hate the locked down manufacturer and AA options where they decide what apps I'm allowed to install, including the Launcher but also importantly things like Ecutek (for this car) or Real Dash (Stagea) are not supported. Plus those crippled versions tend to be slower due to both overheads and lower spec hardware. On the other hand, when this breaks I'll likely be in trouble for support....but how is that different to owning an Infiniti anyway
×
×
  • Create New...