Jump to content
SAU Community

Recommended Posts

  • Replies 255
  • Created
  • Last Reply

Top Posters In This Topic

it's taken me a while but here are some of the photos i took on the day. i haven't had time to look at any of the others, i'm afraid. it wasn't so easy to get wider shots of any of the cars because they were parked so close together. also i've worked out that shooting cars isn't easy! i have a lot to learn.

scn11.jpg

scn09.jpg

scn01.jpg

scn13.jpg

scn02.jpg

scn04.jpg

scn05.jpg

scn06.jpg

scn07.jpg

scn08.jpg

scn03.jpg

scn10.jpg

scn12.jpg

scn14.jpg

yaha cheers chaps. actually i don't have a lot of experience shooting people - more stuff that i can control and position. same goes for lighting. so shooting cars that someone else has parked, with broad daylight and only one lens was bloody tough i found.

but mark (?) was sitting there and the composition was right so i started snapping. i think he said something like 'what's this for?' and i was tempted to say 'autosalon' or something but i told him the truth. :( i think that shot in particular could do with some post work. would look good in b+w. also have a couple more of mrs.gt, jayce. they'd look good with more work too i think.

i'm always up for a shoot so if anyone wants to do a photoshoot or summat i'm keen.

Sorry to rain on the parade,but that'd be a gold Foz,not a Stage' in that reflection. I can understand how you got them mixed up; family wagons,both,with a bit more go than expected in each...LOL! It's all good,Termi'; it just means you can lay a good guilt trip on Sig' for missing your car,and pestering him for an exclusive photoshoot,LOL!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...