Jump to content
SAU Community

Recommended Posts

Hi Guys,

Had my car on the dyno today getting my pfc tuned. Asked the mechanic if we could run it on 12 psi.

This afternoon when I went and picked it up he said that he could not get any more than 9psi. He said that he thinks one of the waste gates was stuck open, does this sound right. It's a 32 gtr with standard turbos and a manual boost controller. Chris

Link to comment
https://www.sau.com.au/forums/topic/151108-boost-problem/
Share on other sites

A stuck wastegate will stop you running higher boost for sure but if your mechanic/tuner can't ascertain the nature of the fault then you might want to consider taking it somewhere else. A good mechanic/tuner is worth his/her weight in gold, especially when talking boost.

Have you ever been able to run more than 9? Does it have a stock computer (My 33 GTR has the stock boost restrictor in place but was running 13psi - found it had an aftermarket computer).

2nd opinion can never hurt, try to find someone who knows Imports and particularly GTR's.

Link to comment
https://www.sau.com.au/forums/topic/151108-boost-problem/#findComment-2812727
Share on other sites

A stuck wastegate will stop you running higher boost for sure but if your mechanic/tuner can't ascertain the nature of the fault then you might want to consider taking it somewhere else. A good mechanic/tuner is worth his/her weight in gold, especially when talking boost.

Have you ever been able to run more than 9? Does it have a stock computer (My 33 GTR has the stock boost restrictor in place but was running 13psi - found it had an aftermarket computer).

2nd opinion can never hurt, try to find someone who knows Imports and particularly GTR's.

THANKS it has a power fc, i got a feeling he put the boost controler on the wrong line no matter how much you ajust it still the same boost.

Link to comment
https://www.sau.com.au/forums/topic/151108-boost-problem/#findComment-2812793
Share on other sites

Did you install the PowerFC? Are you sure there's not a boost control module for the PFC installed somewhere?

It does sound like he's doing something wrong though, you should be able to vary boost by 'some' amount if it's on the right line. I've not fitted a controller to my GTR (only had it a week) but on my Series II GTS25T it was installed on the vacuum line between the Intercooler pipe work and the Wastegate actuator. Make sure it's installed the right way too, if it's not it will boost all over the place and you'll be picking up RB26 pieces =\

Edited by ActionDan
Link to comment
https://www.sau.com.au/forums/topic/151108-boost-problem/#findComment-2812853
Share on other sites

Did you install the PowerFC? Are you sure there's not a boost control module for the PFC installed somewhere?

It does sound like he's doing something wrong though, you should be able to vary boost by 'some' amount if it's on the right line. I've not fitted a controller to my GTR (only had it a week) but on my Series II GTS25T it was installed on the vacuum line between the Intercooler pipe work and the Wastegate actuator. Make sure it's installed the right way too, if it's not it will boost all over the place and you'll be picking up RB26 pieces =\

yeh i put the pfc in but it's the same with the standard one.may have to start pulling shit off and have a bit more of a look.

Link to comment
https://www.sau.com.au/forums/topic/151108-boost-problem/#findComment-2812884
Share on other sites

I'd be getting a second opinion before you start ripping it apart. Try to find a reputable tuner/mechanic with Import/GTR experience. Explain the situation to him so he can inspect the wastegates and go from there.

Good luck, let us know how you go :huh:

Link to comment
https://www.sau.com.au/forums/topic/151108-boost-problem/#findComment-2812913
Share on other sites

The issue of safe boost level on stock ceramic GTR turbo's is a contentious one. Many people have safely run about a bar with no issues, many others have reported turbo failures and in some cases engine damage from ceramic dust being ingested. The decision is yours but be warned that pushing the ceramic turbo's WILL reduce their life and increase the risk of failure as does pushing any component harder.

Link to comment
https://www.sau.com.au/forums/topic/151108-boost-problem/#findComment-2813078
Share on other sites

The issue of safe boost level on stock ceramic GTR turbo's is a contentious one. Many people have safely run about a bar with no issues, many others have reported turbo failures and in some cases engine damage from ceramic dust being ingested. The decision is yours but be warned that pushing the ceramic turbo's WILL reduce their life and increase the risk of failure as does pushing any component harder.

yep i wanted to run at about 12.

Link to comment
https://www.sau.com.au/forums/topic/151108-boost-problem/#findComment-2813135
Share on other sites

Doesn't the power FC have its own ebc therefore eliminating the need for the manual one? I got my car tuned to 13 psi and i had the power fc and eboost hooked up. The eboost was controlling the boost levels but when i went to pick the car up the engine light was on. The mechanic said "oh that just happens to skylines with the power fc" which i didnt take kindly since i entrusted my car to him. I came on here "SAU" and found out that the power fc has a boost controller that u can turn off with the hand controller. I did that and BAM! engine light gone...

In all maybe the power fc boost controller and manual boost controller are crossing paths and playing with your boost level? Perhaps disconnect one and see if theres any difference.

Matt

Link to comment
https://www.sau.com.au/forums/topic/151108-boost-problem/#findComment-2814610
Share on other sites

Doesn't the power FC have its own ebc therefore eliminating the need for the manual one? I got my car tuned to 13 psi and i had the power fc and eboost hooked up. The eboost was controlling the boost levels but when i went to pick the car up the engine light was on. The mechanic said "oh that just happens to skylines with the power fc" which i didnt take kindly since i entrusted my car to him. I came on here "SAU" and found out that the power fc has a boost controller that u can turn off with the hand controller. I did that and BAM! engine light gone...

In all maybe the power fc boost controller and manual boost controller are crossing paths and playing with your boost level? Perhaps disconnect one and see if theres any difference.

Matt

maybe he has put the boost controller on the wrong hose.if i was looking in my engine bay what hose should the boost controller be on?at the moment it's on a small hose under the intake.

Link to comment
https://www.sau.com.au/forums/topic/151108-boost-problem/#findComment-2815546
Share on other sites

Doesn't the power FC have its own ebc therefore eliminating the need for the manual one? I got my car tuned to 13 psi and i had the power fc and eboost hooked up. The eboost was controlling the boost levels but when i went to pick the car up the engine light was on. The mechanic said "oh that just happens to skylines with the power fc" which i didnt take kindly since i entrusted my car to him. I came on here "SAU" and found out that the power fc has a boost controller that u can turn off with the hand controller. I did that and BAM! engine light gone...

In all maybe the power fc boost controller and manual boost controller are crossing paths and playing with your boost level? Perhaps disconnect one and see if theres any difference.

Matt

The PowerFC Boost control is a separate part you purchase (the solenoid).

Its the same thing that the Apexi ACV-R uses.

So you need to actually purchase the solenoid separate, and then install it.

It doesnt come with the PowerFC itself

Link to comment
https://www.sau.com.au/forums/topic/151108-boost-problem/#findComment-2815554
Share on other sites

The PowerFC Boost control is a separate part you purchase (the solenoid).

Its the same thing that the Apexi ACV-R uses.

So you need to actually purchase the solenoid separate, and then install it.

It doesnt come with the PowerFC itself

na i dont have pfc boost controller just one of those GFB ones.

Link to comment
https://www.sau.com.au/forums/topic/151108-boost-problem/#findComment-2815581
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
×
×
  • Create New...