Jump to content
SAU Community

Recommended Posts

Does anyone know what the exact the laws on front mount intercoolers upgrades on cars where stock item was side mounted?

Like to know what it basicaly says, It seems that every one who has a skyline / silvia has put one on so must be ok.

Just like to know, Especialy QLD Law?

Thanx.

Link to comment
https://www.sau.com.au/forums/topic/151314-fmic-laws/
Share on other sites

Anyone been booked for having after market inter cooler in the front mount variety?

I have heard a story that your car can be pulled off the road for beeing structurely modified.

I have never had an issue, I gues the good be fussy and get ur for chopping holes in ur car, thats why its best to clean up and holes u have made for piping.

Ive never had an issue with fmic on cars ive had. Dont know the official law tho sorry.

Link to comment
https://www.sau.com.au/forums/topic/151314-fmic-laws/#findComment-2816637
Share on other sites

If you are worried i think Trust & HKS make cooler kits where the piping reverts back to the stock location - meaning no holes need to be cut

Im looking into this myself for my r33

Yes, don't go cutting holes in your sheet metal, I got defected for this - apparently effects crumple zones and is illegal. Cop who did me said they pull over everything with a shiney front mounted intercooler - maybe best to paint it matt black.

Link to comment
https://www.sau.com.au/forums/topic/151314-fmic-laws/#findComment-2816665
Share on other sites

i got pulled over the other day by cops for speeding and they check my car out and didnt say anything about the FMIC, but a mate of mine got done because his was too shiny! defected for being a distraction to other motorists, so he took it back when the core had oxidised and it was okay'd? (twats)

Link to comment
https://www.sau.com.au/forums/topic/151314-fmic-laws/#findComment-2823542
Share on other sites

Guest 40th-edition

Even though i live in NSW im not sure of QLD laws i get done under the emissions act to do with the EPA and defected off the road for having an FMIC, so stuffed around for ages and went to get it engineered and then found out about the front impact bar being modified and have not found a solution other than changing the hole front end with a gtr bar and guards and bonnet and impact to get it oked by my engineer!!

Link to comment
https://www.sau.com.au/forums/topic/151314-fmic-laws/#findComment-2824711
Share on other sites

i got pulled over the other day by cops for speeding and they check my car out and didnt say anything about the FMIC, but a mate of mine got done because his was too shiny! defected for being a distraction to other motorists, so he took it back when the core had oxidised and it was okay'd? (twats)

Too shiny , what about the old cars with chrome bumper Bars and Chrome grills ?,

intercoolers cant be much brighter than chrome . >_<

Link to comment
https://www.sau.com.au/forums/topic/151314-fmic-laws/#findComment-2825248
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...