Jump to content
SAU Community

Removing front bar on S1 R33 GTSt

Airzone
 Share

Recommended Posts

Dawzey Collaborator

Dawzey

Posted
Posted

if it is an after market bar they are only held ony by like 4 or 5 bolts.

but if it is the plastic one then the bolts are all the way around

so go to wheel and undo the outside ones and undo them one by one and the bar should rap off if u get what i am saying....

benm Grand Master

benm

Posted
Posted

When I had my car at the exhaust place getting some work I wanted them to adjust my IC pipes and re-position the IC. They said they couldn't get my S1 M-Spec bar off coz it was joined into black plastic behind it...

Anyone know anything about this ?

predator Grand Master

predator

Posted
Posted
When I had my car at the exhaust place getting some work I wanted them to adjust my IC pipes and re-position the IC. They said they couldn't get my S1 M-Spec bar off coz it was joined into black plastic behind it...

WTF ? sounds like they didn't know what they were doing and making excuses (common workshop practice).. on mine at least (series1) which has an aftermarket GTR style bar.. although they are much the same i think .. push plastic splash guards in .. remove few screws (2 or so.. or maybe just the one) on left and right side of the bar, bolting bar to side panels. U might need small screw driver, not heaps of room to do it. Some may have had plastic ties to tie the bumper to the splash bits to secure them in place.. just cut them off and replace later.

Now get underneath and there should be 2 support rails where it bolts in the chasis and 2x 14mm bolts each side (from memory, or it could be a 16mm) that holds it in.. You may need a "long socket" (about $8 from a tool place) as the thread comes out a fair bit from the nut. Now undo those 2 bolts on each side.. get something soft to put it on so you don't scratch it.. and simply slide out. You may at that point also need to disconnect the indicators plugs and things.

Hope that helps.

benm Grand Master

benm

Posted
Posted

It does and I do think they were making excuses. Don't spose anyone has pics of where all the bolts and stuff are, much easier then me spending an hour looking for all these hidden bolts (or disconnecting the wrong thing).

  • 1 year later...
  • 1 year later...
nsta Mentor

nsta

Posted
Posted (edited)

hey this would really help me guys, the 2 x 14mm bolts on each side, are they to take off the reinforcement bar as well???, these things are ultra hard to get out, any help pleasE??wrong tools maybe?

heres the order ive done for my r33 series 1 front

pull out the grille (5 plugs)

unplug screws below the grille

-Behind the plastic inner wheel arch guard there's two screws either side which hold the sides of the bar to the front of the guards.

Edited by nsta
  • 7 months later...
  • 1 month later...
Shayde Mentor

Shayde

Posted
Posted

In my experience in removing my factory S1 front bar, there were 2 bolts either side where the front bar meet with the guard, near the wheel arch.

There were then 4 bolts underneath the front bar, staring the the ground. A simple philips screwdriver will get these 4 out. There are 2 on both sides.

There were then 3 clips underneath the grill. When I say grill, I mean the little section that clips onto the headlights and sits between the bonnet and front bar.

Sometimes, you will get lucky and removing these 8 bolts and 3 clips is enough. However, there is a large clip underneath each headlight that the bumper slides under. A flat head screw driver to pry these up will do the job. If you haven't got a tool suitable, you may need to remove the headlights. If this doesn't help, send me a PM and I'll ATTEMPT to draw up a diagram.

  • 4 months later...
bombastic Collaborator

bombastic

Posted
Posted

I can't seem to find the 4 bolts facing the ground. I found 2 facing the front of the car, underneath the grill. I found the 3 clips underneath the grill. Hmm...

I couldn't get the 2 clips off on each side that were attaching the front bar to the guard... philips head just ate the plastic. Tried destroying them with some clippers but the plastic is too tough. Anyone know how to get the clips off without a philips head...?

In my experience in removing my factory S1 front bar, there were 2 bolts either side where the front bar meet with the guard, near the wheel arch.

There were then 4 bolts underneath the front bar, staring the the ground. A simple philips screwdriver will get these 4 out. There are 2 on both sides.

There were then 3 clips underneath the grill. When I say grill, I mean the little section that clips onto the headlights and sits between the bonnet and front bar.

Sometimes, you will get lucky and removing these 8 bolts and 3 clips is enough. However, there is a large clip underneath each headlight that the bumper slides under. A flat head screw driver to pry these up will do the job. If you haven't got a tool suitable, you may need to remove the headlights. If this doesn't help, send me a PM and I'll ATTEMPT to draw up a diagram.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Best place to order Authetic R32 Parts in Japan

      By GTSBoy · Posted

      I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
    • GTSBoy
      Ethanol Content Sensor - Always at 11%?

      By GTSBoy · Posted

      The hydrocarbon component of E10 can be shittier, and is in fact, shittier, than that used in normal 91RON fuel. That's because the octane boost provided by the ethanol allows them to use stuff that doesn't make the grade without the help. The 1c/L saving typically available on E10 is going to be massively overridden by the increased consumption caused by the ethanol and the crappier HC (ie the HCs will be less dense, meaning that there will definitely be less energy per unit volume than for more dense HCs). That is one of the reasons why P98 will return better fuel consumption than 91 does, even with the ignition timing completely fixed. There is more energy per unit volume because the HCs used in 98 are higher density than in the lawnmower fuel.
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      No, I'd suggest that that is the checklist for pneumatic/hydraulic adjustable systems. I would say, based on my years of reading and complying with Australian Standards and similar regulations, that the narrow interpretation of Clause 3.2 b would be the preferred/expected/intended one, by the author, and those using the standard. Wishful thinking need not apply.
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      Yes they do. For some maybe. But for those used the most by abusers, ie Skylines, the numbers are known. The stock eyebrow height for R32/3 Skylines is about 365/375mm or thereabouts. The minimum such heights are recorded in adjacent columns in the database.
    • soviet_merlin
      Ethanol Content Sensor - Always at 11%?

      By soviet_merlin · Posted

      Hmmm, interesting. Makes me wonder whether there is bias as well. It's the cheapest fuel, so it is used for all kinds of ill-maintained shitboxes which are bound to have issues regardless. Nicer cars tend to require higher octane rated fuel and can't use it anyway. FWIW, the official NSW E10 facts page is decent. 
×
×
  • Create New...